Table of Contents
A pressure washer stalling when the trigger is pulled is mostly due to a faulty unloader valve, O-rings, pressure washer trigger, or a too-high setting of the unloader valve. The unloader valve cycles the water back to the inlet, diverting the flowing through the pump system.
Why does my pressure washer stall out when I pull the trigger?
If a pressure washer stalls when the trigger is released, this usually indicates a fault in the unloader valve. It is a simple process to remove and replace the unloader.
Why does pressure washer keep stalling?
A clogged carburetor is most commonly caused by leaving fuel in the pressure washer for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the engine to run stall.
How do I know if my pressure washer unloader is bad?
Water leaks and inconsistent behavior are also signs of a potential failure in the near future. González: The typical signal when there is an unloader malfunction is a reduction of flow through the nozzle, which results in pressure loss. Dean: Typical symptom of an unloader failure is a sudden smooth pressure loss.
Can you adjust an unloader valve?
Now while the gun is engaged you can adjust the pressure by turning the adjusting knob between the two nuts and the nylock on top. If you adjust the unloader without the gun engaged, when you do engage the trigger parts in the unloader move rather violently and could damage the unloader.
Why does my Nilfisk pressure washer keep cutting out?
Problem: The pressure washer cuts out. If your machine cuts out occasionally, it could be because you are using an electric extension cable. Extension cables must always be 13 amp constant rating and no longer than 20 metres. Please check your operating instructions for correct specifications.
How do you unstick a unloader valve?
How to Remove the Pressure Washer Unloader Valve Install a high-pressure tip on the pressure washer. Locate the nut located on the top of the unloader valve. Turn the pressure adjusting knob in a counterclockwise direction until it is completely removed.
Can I start my pressure washer without water?
Although you can start a pressure washer without water, it is not advisable to do it. The water helps to lubricate the pump and help to keep it cool. Without the lubrication and cooling properties of the water, dry starting will cause the pump to wear down quickly.
How do you diagnose a bad unloader valve?
To diagnose a problem in the unloader valve of your pressure washer, you need to check the output pressure of the pressure washer. If it is inconsistent and you see sudden changes in the pressure, it is clear that your unloader valve has a problem.
What happens if unloader valve is bad?
A failed unloader valve can cause high pressure at the nozzle. The unloader valve recirculates water to the pump inlet when the pump is running but the spray wand isn’t in use. A defective pressure regulator can cause high pressure at the nozzle.
What is a trapped pressure unloader?
A trapped pressure unloader is a simple valve with a spring mechanism mounted in a Brass body. There is A channel within the body that gives water access to the back of a piston. When the trigger is released the pressure against the piston increases and pushes the spring open to allow the water to pass into the bypass.
What is the purpose of a pressure washer unloader?
The unloader diverts the flow of water from the outlet side of the pump back to the inlet side, causing water to flow in a loop back to the pump under virtually no pressure rather than to the nozzle under operating pressure.
Why does my pressure washer keep starting and stopping?
Water leaking from a loose connection can cause the unit to cycle on and off. Verify if the pressure hose has an O-ring at the connection. If missing, this will also cause the unit to cycle on and off. While the unit is running look for any water leaks that may cause the unit to turn back on.
Why has my Nilfisk stopped working?
Pump sucking Valves dirty, worn out or stuck Pump seals worn out Check that hoses and connections are airtight. Clean and replace or refer to local Nilfisk distributor. Machine stops Fuse has blown Incorrect mains voltage Thermal sensor activated Nozzle partially blocked Replace fuse. Switch off other machines.
How does the unloader valves work?
Essentially, an unloader valve is a safety switch. It sends pressurized water into a by-pass by cycling it from the outlet side of the pump to an inlet or water tank. This process depressurizes the water and prevents pressure from building up while the pressure washer machine is idling.
What is a pilot unloader valve?
Piloted unloader valves combine a pilot valve and an unloader valve to run an air compressor continuously. While this type of valve is most commonly used on gas-powered air compressors, it can also be used on electric models. The unloader valve then closes and the pressure begins to build again and repeats the cycle.
Can you adjust PSI on pressure washer?
Can I adjust the PSI on my pressure washer? You simply turn the dial to increase or decrease the pressure. Others have a regulator on the spray wand, similar to the Vario wand on our electric power washer. You can also change out the nozzle tips which alter the impact pressure when spraying.
Should I run my pressure washer at full throttle?
Chesebro: Do you guys full throttle your machines even when soft washing? Yes because of the reasons Thad states you should run your engine at full throttle at all times. Jul 30, 2014.
How does the governor work on a pressure washer?
How Pneumatic Governors Work. The speed-sensing device on a pneumatic governor is a movable air vane, made of metal or plastic. This small engine part registers the change in air pressure around the spinning flywheel. As the load lessens and engine speed increases.
