Table of Contents
The optical cable is not securely connected. The optical cable may be faulty. The TV may require a system software (firmware) update. Downloads are posted on your model support page.
How do I know if my optical cable is bad?
To troubleshoot, plug the suspect connector into the VFL and look at its back. If a lot of red light is visible, the connector is bad and should be replaced. If you look from the other end and see light coming only out of the fiber, that indicates a good connector. If the whole ferrule glows, it’s bad.
Why does my TV audio cut in and out?
Intermittent audio can be electronics in the Review, bad cable or contacts, or the TV itself. Start by reseating the HDMI cable at both ends; check to see if the contacts are dirty. Use another HDMI source (borrow if you don’t have one) to see if it’s the Review. Finally, see if another HDMI TV eliminates the problem.
Why did my optical audio stop working?
The optical cable isn’t securely connected. The optical cable may be faulty. Your TV isn’t updated with the latest software version. The connected third-party sound bar, or home theater system may not be compatible with your TV.
Why does my soundbar keep cutting out?
Your soundbar may cut out audio due to several reasons. It may be Bluetooth interference, old worn-out components, inadequate wire gauges, outdated software, and even poorly connected cables.
What happens when an optical cable goes bad?
Like all other cables, the joint between the plug and the cable tubing can come undone. If this happens, the cable may stop working. Further, fiber optic cables are much more sensitive to crimping than standard wire cables. Even pinching the wire too much can cause the fiber optics to get damaged.
Are optical audio cables fragile?
The official term for optical audio cable is “Toslink,” short for Toshiba Link. You’ve seen standard S/PDIF connections a bunch too; they’re often called “coax digital.” Optical had certain benefits over copper cables, but they were also more fragile, and for a long time, more expensive.
How do I fix the sound cut out on my TV?
Increase the volume on the TV and/or your connected media device (streaming player, Blu-ray player, cable or satellite box, etc.). Check the audio settings on your TV and connected devices. Turn off and unplug your TV and connected devices. Inspect the TV cables and ports, then check the ones on your devices as well.
Why does the sound keep cutting out on my LG TV?
Check if the TV Sound Out is set to TV Speaker. Check if the correct input is selected on the TV. Check if the TV volume is set to the correct level and not muted. If the external source, such as a cable or satellite box has a volume control, check if the setting is muted or set at a low volume.
Why does my HDMI sound cut out?
It could be something as simple as a loose connection on the back of the AV source device, or just a simple cabling issue. Check your HDMI cables and connections – Make sure that everything is seated in the right place, plugged in where it should be, connected properly.
Is optical better than HDMI?
In terms of audio quality – HDMI wins If you’re looking for the best audio quality, HDMI is your choice. While an optical cable can still pass surround sound and super high-quality audio, thanks to the added bandwidth in the latest HDMI versions (2.0) you’ll be able to pass higher resolution and audio.
Is digital audio out the same as optical?
The audio signal stays in a digital format using either of these cables. The differences between the two connections are as follows: A Digital Optical connection uses a fiber optic cable. The digital audio bit stream is transmitted using pulses of light through this optical cable.
Is PCM better than compressed?
If the only thing you have is the television speakers for your entertainment, the PCM setting is the best option because it lacks compression. You’ll hear muted tones and less audio clarity when using the Dolby Digital setting with your stock setup.
Why does my Samsung sound bar keep cutting out?
The sound on your wireless subwoofer can drop out if there is interference or a physical obstruction between the soundbar and subwoofer. You can try checking the firmware version, resetting, and reconnecting the subwoofer.
Does fiber optic cable wear out?
The fiber optic thread is not an active source that generates electricity. Fiber optic connections don’t degrade over distance, unlike cable broadband and DSL, allowing for consistent premium data transfer speeds.
How do you clean an optical audio port?
You can use a special solution for fibre optic or 91% Isopropyl Alcohol. Wipe the end face against the wet area and then onto a dry area to clean potential residue from the end face. Wet cleaning is more aggressive than dry cleaning, and will remove airborne contamination as well as light oil residue and films.
Should optical cable click in?
When you insert the optical cable, it should click into place. It is designed to fit one way only; one side is squared-off while the opposite is angled on the corners.
