Table of Contents
How big should the Notch be when cutting a tree?
The notch cut consists of two intersecting cuts that converge perpendicular to where you want the tree to fall. The width of the cut should be 80 percent of the tree’s DBH (diameter at breast height). In my case, my tree was about 10 inches wide at my chest so the optimal length for my notch was eight inches.
Why do you notch a tree to cut it down?
A classic example of this is the conventional method of falling trees, where a 45 degree notch is cut into the tree being felled. A simple way to avoid hinge failure and loss of control when falling trees is to cut a notch opening that allows the hinge to stay working and in control until the tree is on the ground.
How deep do you notch a tree?
6 The depth of the notch should be 1/3 of the tree diameter. The face opening of a notch “A” should be equal to the depth of “B”. An open face notch is safest and requires an opening of 70% or more to prevent premature closing of the notch.
What is a Dutchman in tree felling?
Dutchman. The seat that interferes with the smooth closing of the notch. Caused when one of the notch cuts is made too deep and extends beyond the endpoint of the other notch cut, known as “Bypass”.
How do you mark a tree for cutting?
Always use stump marks for any tree marked for cutting, as a leave tree, or as a boundary tree. Ensure that the mark is at or near the ground line, but on the tree and not the ground. Make the stump mark large enough to be conspicuous if scraped or chipped off.
Which way will a tree fall when cut?
Plan the Notch The notch is what will allow the tree to fall properly, so you want it on the “fall side” so the tree will fall in the direction of the notch. The fall side should be the heaviest side of the tree. Cut at a comfortable working height.
How do I cut down a tall tree around my house?
In order to get rid of a tree that is over 20 feet tall near your house: Clear the area of vehicles and items that may be damaged by falling branches or trunk sections. Use a chainsaw and employ the 3 cut method to safely remove large lower branches. Use a reciprocating saw to remove upper branches.
Which way will a tree fall in a storm?
A tree will most likely fall in the direction of the lean.
What side of the tree do you make the first cut?
Step 3: Make the First Cut With the tree on your left and your left shoulder against the tree, make a 70-degree cut on the side facing the direction you want the tree to fall. If your chainsaw has a felling sight on the housing, use it as a guide.
How do you get a tree to fall the opposite way its leaning?
A tree leaning away from the intended direction of fall has “back lean.” By using wedges and shims to lift the trunk off the stump, you can compensate for the back lean and bring the tree up and over in the intended direction.
What is a Dutch cut?
Sometimes it’s necessary to set a job up to use irregular cuts. These are sometimes called a Dutch Cut which means to cut in one direction of the grain, then to turn the piece and cut it another direction.
What is a Humboldt cut?
The Humboldt notch is another common notch when cutting trees. In this notch, the top cut is made horizontally, while the base goes in at an upward point. In this type of notch, the kickback over the stump may be bigger, so it is not perfect for inclining trees.
What does it mean when a tree barber chairs?
A barber chair occurs when a tree being felled delaminates vertically before the hinge is cut thin enough to bend. The term refers to the sliding action of the old style barber chair that positioned patrons in a head down, feet up position so the barber could more easily shave with the straight razor.
What does green tape on a tree mean?
Green paint ring around the tree trunk indicates a mountain pine beetle infested tree on commons.
What does pink paint on trees mean?
Tree marking was put into place to provide a mechanism for measurement, convey to the timber purchaser which trees are to be removed or remain, and help prevent and detect timber theft more easily. It provides a means to utilize and improve timber product accountability and reduce losses.
What does white paint on trees mean?
Painting the trunks of trees with a white latex (do not use oil-based paint) is a way to protect the trees from southwest injury. White is used because it is not harmful to the tree and is effective at reflecting sunlight to moderate changes in the temperature of the trunk.
How do you cut a tree with a hand saw?
Trim branches and limbs that will make cutting the tree down easier, or could prove dangerous during your work. Use your handsaw and make a cut on one side of the branch, cutting about a third of the way through. Switch to the other side and continue cutting until the branch falls off.
What is the three cut method?
Next cut downward from the top of the branch several inches beyond the first cut. As the branch starts to fall, it will break away at the first cut. This prevents damage to the trunk. The third and final cut is made flush with the branch bark collar.
Should I remove a tree close to house?
Trees hanging over the roof or too close to a structure might need to be removed – or at least regularly pruned. In general, large trees should be at least 20 feet away from a house or building.
