Table of Contents
A mousetrap car can be made from cardboard or balsa wood with CD’s for wheels and axles of wood or brass tubing. Power to drive the wheels is provided by a mousetrap to which a wand and string is attached to the snap arm.
How do you get a mousetrap car to move?
If a mousetrap vehicle is struggling to move and/or needs more acceleration then the lever arms can be shortened in order to increase the pulling force. Keep in mind that you will also have to reposition the mouse trap closer to the drive axle or the system will not work as intended.
How long should the lever arm be on a mousetrap car for distance?
For maximum speed, position the mousetrap 2 1/4 inches from the drive axle and cut the lever arm to a length of 4 1/4 inches. The lever arm can be cut using a dremel tool or by using a fine tooth hobby saw. The lever arm should always be “just” long enough to reach the drive axle or performance will be compromised.
How long should a mousetrap car be?
The ideal size for an ultra big wheel on a long distance mousetrap racer seams to be somewhere between 10 and 15 inches. And the ideal size for a drive wheel on a speed-trap racer seams to be between 2 and 3 inches but no more than 4 inches.
What kind of string do you use for a mousetrap car?
The string has to be strong enough to handle the pulling force but flexible and thin enough to wind tightly around the drive axle. We recommend using a Kevlar based fishing line because its high strength. You should stay away from nylon fishing line and dental floss, these do not work well with mousetrap racers.
What makes a mousetrap car go farther?
Using large rear wheels allow one rotation of the axle to take the car a much further distance. In other words, a given length of the string from the mousetrap moves the car a greater distance. In non-technical terms, this means that the same force from the mousetrap on each snap gets exerted over a longer string pull.
Should a mousetrap car be heavy or light?
Above all, your car should be light. The smaller the mass of your car, the better — every gram or milligram you can shave off of your car’s frame is a little further your mousetrap will be able to push your car.
What is an axle hook on a mousetrap car?
An important part of a mousetrap vehicles propulsion system is the axle hook. If the string does not properly release from the drive axle the string will rewind around the drive axle and cause the mousetrap car to come to an instant stop.
What does the lever arm do on a mousetrap car?
Changing the length of a mouse trap’s snapper (or lever arm) is how you control a mousetrap vehicle’s acceleration and/or travel distance. Different lengths of lever arms can be used to increase and/or decrease the pulling force and change the amount of string that can be pulled off the drive axle.
What materials do you need for a mousetrap car?
What You Need: Wooden snap-back mousetrap. Duct tape. 4 eye hooks. Wooden dowel that fits inside the eye hooks. Heavy cardboard. Large and small rubber bands. Foam board (usually found at a craft store) String.
Does a faster mousetrap car mean a further distance?
A speedy mousetrap car will have smaller wheels (faster acceleration), a shorter lever arm (increased torque, but smaller travel distance), a larger axle (increased acceleration) and will generally be smaller to decrease air resistance.
How far do mousetrap cars usually travel?
The average distance the rattap car went was 18.6875ft and the average distance the mousetrap car went was 25.5ft.
How far did the world record mousetrap car go?
Description: The secret to Doc Fizzix’s world record setting mousetrap distance racer that traveled over 182 meters was it’s unique pulley system. This is the same pulley set-up that was used on Doc Fizzix’s world record setting mousetrap distance car.
What can you use for wheels on a mousetrap car?
As you might guess, the materials used to build mousetrap-powered cars are light out of necessity. Foamcore board or balsa wood are often used for the body. The wheels can be off-the-shelf radio-controlled car wheels, but many builders use blank CDs or DVDs because their thin edges reduce friction.
Why is my mousetrap car not going straight?
If your mousetrap car does not travel straight energy is also being wasted to over come the force of friction turning the vehicle’s wheels. If a mousetrap vehicle is not traveling straight then there is one reason and one reason only: the front and rear axles are not parallel to one another!Jan 21, 2012.
What is the fastest mousetrap car?
The Speed-Trap Racer is the fastest mousetrap powered racer anywhere and was designed after Doc Fizzix’s own record-setting mousetrap racer that traveled 5 meters in 1.2 seconds.
How do mousetrap cars reduce friction?
Try to have a minimum gap of 1/8 inch between the frame and any spacers (or wheels) in order to decrease any rubbing friction. Use thrust washers and graphite powder between spacers (or wheels) and the frame to help reduce the rubbing friction.
Is weight important in a mousetrap car?
Reduce the most friction you can because the more friction the more energy is lost in propelling the car. Mass should also be taken into account, the more the car weighs the more energy from the mousetrap spring will be used so it’ll be best to make the car light weight.
Why is it better to have large wheels for the drive axle on a mousetrap car?
Larger drive wheels will have a greater travel distance per each turn compared to smaller drive wheel. The smaller the diameter of the drive axle in comparison to the diameter of the drive wheel the more force that will be required to accelerate the vehicle but the greater the distance of travel per rotation.
