Table of Contents
A mousetrap car works on the principle of a lever. One end of the lever is connected to a spring. When a force is used to pull up the other end of the lever up, the spring tightens, storing energy. When the lever is released, the stored energy in the spring is transferred back to the lever, and the end snaps back.
How does a mousetrap car work?
The mousetrap storespotential energyin the form of the spring. That potential energy is converted into kinetic energy in the form of the arm rotating forward. The arm pulls on the wound-up string, which turns the drive wheel dowel, which is connected to the wheels, which makes the car drive forward.
What force does a mousetrap car use?
Friction is a force that acts against the motion of all moving objects. Energy is required to overcome friction and keep an object moving. Mousetrap cars start with a limited supply of energy. This energy is used to overcome friction and propel the vehicle.
How do you make a mousetrap car move?
If a mousetrap vehicle is struggling to move and/or needs more acceleration then the lever arms can be shortened in order to increase the pulling force. Keep in mind that you will also have to reposition the mouse trap closer to the drive axle or the system will not work as intended.
What makes a mousetrap car go farther?
Using large rear wheels allow one rotation of the axle to take the car a much further distance. In other words, a given length of the string from the mousetrap moves the car a greater distance. In non-technical terms, this means that the same force from the mousetrap on each snap gets exerted over a longer string pull.
What makes a mousetrap car go faster?
A speedy mousetrap car will have smaller wheels (faster acceleration), a shorter lever arm (increased torque, but smaller travel distance), a larger axle (increased acceleration) and will generally be smaller to decrease air resistance.
Can a mouse trap break your finger?
A mouse trap might not break your finger, but it’ll hurt. Rat traps, though, which are about 4 times larger and stronger than mouse traps and usually have serrated edges, could break your finger. If they don’t break your finger, you could still have severe bruising or pinched nerves.
How long should the lever arm be on a mousetrap car for distance?
For maximum speed, position the mousetrap 2 1/4 inches from the drive axle and cut the lever arm to a length of 4 1/4 inches. The lever arm can be cut using a dremel tool or by using a fine tooth hobby saw. The lever arm should always be “just” long enough to reach the drive axle or performance will be compromised.
Should a mousetrap car be heavy or light?
Above all, your car should be light. The smaller the mass of your car, the better — every gram or milligram you can shave off of your car’s frame is a little further your mousetrap will be able to push your car.
How far does a mousetrap car go?
The average distance the rattap car went was 18.6875ft and the average distance the mousetrap car went was 25.5ft.
How do mousetrap cars reduce friction?
Try to have a minimum gap of 1/8 inch between the frame and any spacers (or wheels) in order to decrease any rubbing friction. Use thrust washers and graphite powder between spacers (or wheels) and the frame to help reduce the rubbing friction.
What is an axle hook on a mousetrap car?
An important part of a mousetrap vehicles propulsion system is the axle hook. If the string does not properly release from the drive axle the string will rewind around the drive axle and cause the mousetrap car to come to an instant stop.
How far did the world record mousetrap car go?
Description: The secret to Doc Fizzix’s world record setting mousetrap distance racer that traveled over 182 meters was it’s unique pulley system. This is the same pulley set-up that was used on Doc Fizzix’s world record setting mousetrap distance car.
What is the fastest mousetrap car?
The Speed-Trap Racer is the fastest mousetrap powered racer anywhere and was designed after Doc Fizzix’s own record-setting mousetrap racer that traveled 5 meters in 1.2 seconds.
How do you get more torque on a mousetrap car?
The gearing of a mousetrap car determines the acceleration and the travel distance.Increase the torque by any of the following: shorten the length of the lever arm. using a smaller diameter drive wheels, or. increase the diameter of the drive axle.
What materials do you need for a mousetrap car?
What You Need: Wooden snap-back mousetrap. Duct tape. 4 eye hooks. Wooden dowel that fits inside the eye hooks. Heavy cardboard. Large and small rubber bands. Foam board (usually found at a craft store) String.
Do mice squeak when caught in trap?
Yes, they squeak when trapped. However, don’t consider mice squeaking as the only sign of them getting trapped. In some cases, you may not hear the squeaks mice make when they stuck into a trap. Also, in some traps, the caught mice may die before making any sound.
Do mice feel pain when trapped?
Once trapped by the glue board, mice will struggle for hours until they eventually die of starvation. Sometimes their flailing causes their heads to get caught as well, leading to slow and painful suffocation. Equally as cruel, poison causes significant pain in the slow process to kill rodents.
Will mice bite me in my sleep?
Can Mice Bite You In Your Sleep? While sometimes rats are known to bite people in their sleep, the change of getting bitten from a mouse is extremely rare. If they’ve darted across you while you were sleeping, it’s most likely because you’re a shortcut from Point A to Point B.
What does the lever arm do on a mousetrap car?
Changing the length of a mouse trap’s snapper (or lever arm) is how you control a mousetrap vehicle’s acceleration and/or travel distance. Different lengths of lever arms can be used to increase and/or decrease the pulling force and change the amount of string that can be pulled off the drive axle.
How do you fix this mousetrap car suddenly stops or slows quickly?
Axle Points Test spin your mousetrap racers wheels in order to see how friction-free they spin. If the wheels stop spinning fairly quickly then you will need to find ways to reduce the axle friction. Try using graphite powder or even replacing bushings with ball bearings.
