Table of Contents
Pool stabilizer is also known as pool conditioner, chlorine pool stabilizer, chlorine stabilizer, or Cyanuric Acid. It’s also included in chlorine tablets or sticks (called trichlor) or shock (called dichlor).
Does pool shock have stabilizer in it?
Liquid chlorine and granular shock have the same active chemical that sanitizes your pool, what changes is the strength and the way you use it. Liquid chlorine is less costly, unstabilized and comes in liquid form. Granular shock is stabilized and comes in a solid form that dissolves in your pool.
Can you shock your pool and add stabilizer at the same time?
There is no ironclad rule, but you should never shock the pool immediately after you add stabilizer. Never shock your pool after adding stabilizer if the pH and chlorine levels are balanced. That would waste the chlorine you may have to drain and backwash some water to fix the problem.
What is pool stabilizer?
Pool stabilizer is also sometimes called pool conditioner, chlorine stabilizer, or cyanuric acid (CYA). Its purpose is to stabilize the chlorine in your pool water, so the sanitizer lasts longer. When UV rays from the sun hit the water, chlorine starts to evaporate, leaving very little free chlorine in your pool water.
Can I use stabilized chlorine to shock my pool?
Cyanuric acid stabilizes chlorine, making it last longer in the pool. It works best with indoor pools where you don’t need to worry about the sun. It can be used as pool shock. It’s ideal for quick doses if your pool is getting heavier than normal use.
What happens if you put too much stabilizer in a pool?
Too much stabilizer can begin to lock the chlorine in your pool (chlorine lock) and render it useless. Chlorine lock symptoms are the same signs as a pool with no chlorine such as cloudy and/or green water and/or a strong chlorine smell.
What happens if you have too much stabilizer in your pool?
Anything above 50 ppm the stabilization effect of CYA starts to level off. Too much CYA in pool water will interfere with the chlorine’s ability to kill bacteria and algae from forming.
What happens if stabilizer is too low in pool?
If your CYA levels dip too low, your chlorine will be completely gone in a few hours and your swimming pool will become susceptible to bacteria and algae growth. If the pool stabilizer levels get too high, however, it overpowers the chlorine and makes it less effective.
When should I add stabilizer to my pool?
The product is typically added to the pool when it is first opened for the summer season. Open your pool under normal procedures, and let the filter run with its normal amount of chemicals. When all the other chemicals, such as chlorine. pH and alkalinity, are balanced, add the chlorine stabilizer.
How long after adding chlorine can I add stabilizer?
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool.
Is baking soda a pool stabilizer?
Baking soda, also known as sodium bicarbonate is naturally alkaline, with a pH of 8. When you add baking soda to your pool water, you will raise both the pH and the alkalinity, improving stability and clarity. Many commercial pool products for raising alkalinity utilize baking soda as their main active ingredient.
How long does stabilizer last in pool?
Pool stabilizer is quite slow to dissolve no matter what method you use. It will take 2-5 days to dissolve fully. There are two methods you can use to dissolve stabilizer into your pool water.
What chlorine has no stabilizer?
Cal-hypo (calcium hypochlorite) This type of chlorine is popular for pool use because it’s relatively cheap. It requires the addition of cyanuric acid to keep it stable in sunlight. Without stabilizer, it can lose 95% of its effectiveness in just a couple of hours.
Which pool shock has stabilizer?
Calcium Hypochlorite is the most common, strongest and cheapest pool shock, available in two strengths, Shock and Super Shock. Dichlor is a stabilized granular pool shock, made with stabilizer to protect it from the sun and keep it active longer during the day.
Can you over shock a pool?
Can you put too much shock in a pool? SKIMMER NOTES: It’s unlikely but it could happen. It would take a lot of shock to really make the water unsafe for swimming. The best way to make sure you’re safe to swim is to test your pool water and make sure free chlorine levels are between 1-4ppm for healthy swimming.
How do I fix too much stabilizer in my pool?
You cannot add chemicals to lower the stabilizer level. Cyanuric acid (a stabilizer) can be added, but to lower it, the pool needs to be diluted with fresh water. There is no chemical on the market that you can add to your pool water to lower the stabilizer.
Do I add chlorine or stabilizer first?
If you add the stabilizer first, then the chlorine shock you add will not break down quite as quickly in sunlight, but will also be less effective.
Will low stabilizer cause cloudy pool?
The only way to lower CH levels is to partially drain and refill your pool water. As such, remember to keep CH levels between 200 and 400 ppm all the time. Other chemical imbalances: High levels of accumulated phosphate and bromine and imbalanced stabilizers, such as cyanuric acid (CYA) might also cause cloudiness.
Why is my pool still green after shock and algaecide?
When shock chlorine oxidizes the copper, it turns green and that’s what you’re seeing in the pool. To get rid of it you’ll need to raise the pool’s calcium hardness by adding calcium chloride. The other culprit can be high levels of pollen.
