Table of Contents
How much does it cost to replace an inducer motor?
Although the range can be anywhere from $85 to $1,150, the average cost of replacing a furnace inducer motor is typically between $245 and $465. When the damaged or broken part is under warranty and all you’re paying for is labor to have it installed you can expect to pay around $245.
Can you replace a furnace motor yourself?
With our furnace blower replacement guide, you can do it yourself and save. The typical service call for a hvac technician to do this would cost several hundred dollars but you can save most of that money by doing it yourself. Our guide will walk you through the process of diagnosis, motor selection, and replacement.
How much does it cost to replace blower motor in HVAC?
An HVAC blower motor replacement costs an average of $450 but anywhere from $150 to $2,000 to replace. It doesn’t matter if you have a gas furnace, electric or heat pump, they all use an air handler blower motor to push the air throughout your home’s ducts.
How long should a furnace inducer motor last?
A: On average, you can expect a well-built inducer motor to last around 20 years.
How do I know if my furnace inducer motor is bad?
One of the first indications of a bad draft inducer motor is likely to be the sound it makes. A failing inducer motor may create a noise shortly after a heating cycle begins. This could be a tapping noise, or a humming or whirring sound.
How much is an inducer motor for a carrier furnace?
The average cost of a Carrier inducer motor replacement is between $800-$1800.
How much does it cost to replace a furnace motor?
How much does a furnace motor replacement cost? On average nationwide, a furnace blower motor replacement costs $400-$600, including parts and labor. A single-speed blower motor costs around $450 to replace while a variable-speed motor costs $600+.
Is it hard to replace a blower motor?
If you don’t want to sweat or shiver, then find a good mechanic. The replacement of the blower motor is common and straightforward, so most shops will perform the repair — many on the same day.
What causes inducer motor failure?
Most inducer motors failures are simply attributed to the older age of the furnace. In most cases, the internal bearings wear out and since the unit is a sealed unit, there is no way to repair the original motor. Instead the unit is simply replaced with a new one.
How do you lubricate an induction motor?
Electric Motor Bearing Lubrication Procedure Ensure the grease gun contains the appropriate lubricant. Clean the areas around the relief and fill fittings. Remove the grease relief valve or drain plug. Grease the bearing with a calculated amount of grease. Watch for grease coming out the relief port.
How do you lubricate a furnace fan motor?
If the motor has oil ports, it should be lubricated annually. Apply two or three drops of 10-weight nondetergent motor oil (not all-purpose oil) to each port. Do not overlubricate. If the blower shaft has oil ports, it, too, should be lubricated annually, following the same procedure.
How do I lubricate my furnace blower motor?
Lubricating the Furnace Motor To do so, you have to apply two to three drops of ten-weight non-detergent motor oil to each port. Remember not to over lubricate. You must also check if the blower shafts have oil ports, if it does, just follow the same procedure. This too should be done annually.
How do I know if my HVAC blower motor is bad?
What Are Signs Your Blower Motor Needs to Be Replaced? Poor or Airflow from Air Vents. This will be the first and most obvious sign your blower motor has a problem. No Airflow At All From Vents. Skyrocketing Energy Bills. Strange Noises When You Turn on the Heat. Overheating Blower / Weird Smells.
What are the signs of a bad blower motor?
You might also hear ongoing whirring noises, or noises that change or get louder if you increase the fan speed. These are all signs of problems with the blower motor. In some cases, you may even notice smoke or smells of burning while driving, in which case you should pull over immediately.
How do I know if my HVAC fan motor is bad?
Signs and Symptoms of a Bad AC Fan Motor The fan won’t start even though the AC is on. The fan won’t stop, even when you shut the AC off. The fan turns on, yet the blades are rotating very slowly. There’s a rattling noise coming from the condenser unit when the fan is turned on.
How long does the average furnace motor last?
Even though the manufacturer states their blower motor will last two decades, we advise all clients to expect a 10-20-year life span due to age, use, and proactive maintenance.
Why is my inducer motor noise?
A draft inducer (or vent blower) is the most common problem on a gas furnace or boiler to cause a noticeable noise. The small motor mounted within the housing can begin to make noise when there is buildup on the wheel (such as sulfur or creosote) or when the motor is close to the end of its usable life.
Is an inducer motor the same as a blower motor?
When the furnace receives a signal to begin heating, the draft inducer motor begins spinning. Doing so removes dangerous gases produced during the previous heating cycle, such as carbon monoxide. In essence, the draft inducer motor is nothing more than blower motor, fan, and electrical box.
Can you clean inducer motor?
Spray compressed air where the motor meets the blower wheel housing. This removes dust and dirt away from the blower motor shaft. Wipe the top of the motor with a clean rag to remove dust and dirt from around the oil ports.
