Table of Contents
A high PI indicates an excess of clay or colloids in the soil. Its value is zero whenever the PL is greater or equal to the LL. The plasticity index also gives a good indication of compressibility (see Section 10.3). The greater the PI, the greater the soil compressibility.
Why is the plasticity of clay important?
It’s incredibly important in ceramics as it works in relation to the clay’s ability to assume a new shape without any tendency to return to the old (elasticity). It’s the ability to knead, shape, push, pull and for the clay to remain in that state.
What is highly plastic clay?
The plasticity index (PI) is a measure of the plasticity of a soil. Soils with a high PI tend to be clay, those with a lower PI tend to be silt, and those with a PI of 0 (non-plastic) tend to have little or no silt or clay.
What happens when clay is fired?
Organic matter in the clay is burned and oxidized to carbon dioxide, and fluorine and sulphur dioxide from materials in the clay body are driven off at 1292–1652°F (700–900°C). At this point the biscuit firing is completed. The clay particles are sintered or welded together. The fired clay is known as metakaolin.
What is the plastic limit?
The plastic limit is the water content at which a soil-water paste changes from a semisolid to a plastic consistency as it is rolled into a 3.175-mm (1/8-inch) diameter thread in a standard test.
At what diameter will a soil thread starts to crumble when it reaches the plastic limit?
The plastic limit is when a thread of soil rolled out on a nonporous surface begins to crumble when it reaches 1/8 in in diameter.
Does vinegar dissolve clay?
The trick is vinegar: simply white vinegar from your local grocery store. One word of warning, using vinegar on pieces made using the slip-casting method will break down the clay and it will start to dissolve.
Does Clay shrink when fired?
Clay shrinks both in drying and in firing. Different clay bodies shrink at different rates which can be as little as 4%, or as much as 15% for some clay bodies. We also found through out after years of firing that even with the same clay body, shrinkage can vary 1-2% from batch to batch.
What does the plastic limit tell you?
Plastic Limit (PL) is the water content at the change from a plastic to a semi-solid state. Shrinkage Limit (SL) is the water content where the further loss of moisture does not cause a decrease in specimen volume.
Why does my clay smell?
When clay is stinky, though, it’s usually good, since that smell only comes when the clay has spent some time in the wet condition. If your clay stinks, that’s a good thing. It means there’s bacteria in it, living on the organic matter in it.
What does plasticity in clay mean?
Plasticity is the outstanding property of clay–water systems. It is the property a substance has when deformed continuously under a finite force. When the force is removed or reduced, the shape is maintained.
How do you increase plasticity in clay?
Clay artists tend to think of aging clay as a process of improving the clay’s plasticity by storing it for a long time. Clay that is mixed with a minimum amount of water (so called dry mixed) behaves this way and exhibits increasing plasticity for the first two to four weeks of storage as it becomes fully wetted.
What are the 6 stages of clay?
What are the clay stages?
- slip. a mixture of clay and water, the consistency of pudding.
- wet/plastic clay. new clay from the bag, very workable.
- leather hard. the clay has lost most moisture, but you can still carve into it.
- bone dry or greenware. totally dry clay, all moisture is gone, ready to fire.
- bisque.
What are the 5 types of clay?
Ceramic clays are classified into five classes; earthenware clays, stoneware clays, ball clays, fire clays and porcelain clays.
Is Clay a plastic?
Clay is not a polymers. Polymers are compounds while clay is a mixture. Clay is not a ‘PLASTIC’ it is mud.
What are the 4 types of clay?
The four types of clay are Earthenware clay, Stoneware clay, Ball clay, and Porcelain.
What does grog do in clay?
Grog is used in pottery and sculpture to add a gritty, rustic texture called “tooth”; it reduces shrinkage and aids even drying. This prevents defects such as cracking, crows feet patterning, and lamination. The coarse particles open the green clay body to allow gases to escape.
Why is my natural clay so sticky?
The weather of the area or room that you have chosen for your pottery work can affect your clay’s condition. Your clay is more likely to become soft if the weather gets sultry because the moisture and humidity content makes the clay to retain a lot of moisture, thereby making it soft and sticky.
What are three properties of plastic clay?
There are three essential properties that make clay different from dirt. These are plasticity, porosity, and the ability to vitrify.
Can you apply slip to bone dry clay?
When slip is applied to bone dry clay, one part of the pottery will be much wetter than the next. As such slip won’t stay liquid and doesn’t create the liquid soup for clay particles to move about in. So, generally slip is not used to join pieces of bone dry clay.
What are the four properties of clay soil?
Soil with a large amount of clay is sometimes hard to work with, due to some of clay’s characteristics.
- Particle Size.
- Structure.
- Organic Content.
- Permeablity and Water-Holding Capacity.
- Identifying Clay.
How do you prevent clay shrinkage?
Grog is clay which has been fired then ground up. Grog can come in many particle sizes, from fine to coarse. It is used to reduce shrinkage in clay bodies. The best size of grog for most purposes is a 30/80 mesh.
What does a high plastic limit mean?
A high liquid limit normally indicates a high compressibility and a high shrinkage/swelling potential. A high-plasticity index Ip generally results in a low shear strength. A low Ip means that a soil used as foundation will change significantly in consistency even with a small change in water content.
What does vinegar do to Clay?
Vinegar is also used in clay bodies to increase acidity to improve plasticity. The acid works to neutralize sodium ions (from water, leaching feldspars) that tend to deflocculate the clay. Excessive acid may tend to dissolve more feldspar or nepheline syenite negating the effect.
