Table of Contents
If you have an Irritrol RD-nnnn key and it won’t open: There’s usually a plastic key you turn on the side of the case to open it. While you turn it and keep it turned, pull on the door; they sometimes stick closed a bit.
How do I reset Irritrol rain dial?
Open the battery compartment and disconnect the battery. Press and hold the Manual button in and KEEP HOLDING IT IN while performing the next step. Reconnect the ribbon cable, then release the Manual button. Note: The display should now show 12:00 AM indicating the controller has reset.
How do you reset rain dial sprinkler system?
The current date and time will not be affected. Turn the dial to Seasonal Adjust. Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen. Turn the dial back to AUTO RUN. Your ESP-Me is now restored to the factory default settings.
How do you reset a sprinkler system?
How to Reset a Sprinkler System Turn the control dial to the “off” position. Press the “next” button to access the clear-memory feature. Press and hold the “off” button until the display stops blinking. Turn the control dial to the “run” position. Press and hold down the “minus” arrow and “prog” buttons simultaneously.
How do you adjust Irritrol sprinkler heads?
Rotate the sprinkler turret to the “right start” position and hold it there. Turn the tool clockwise to increase the sprinkler arc and counterclockwise to decrease it. Each full turn of the tool will change the arc by 90 degrees. The arc can be adjusted from 40 degrees to 360 degrees.
What is VC on sprinkler system?
6 – Valve Common Terminal (VC) • Connection terminal for the valve (field) common wire.
Why is my Rainbird not working?
Circuit breaker/fuse – Check the condition of the circuit breaker or fuse, if it has been blown the most likely reason is a field wiring short. An Electromechanical controller will stop on the station that caused the problem. Reset the controller to its rest position and replace the fuse or reset the circuit breaker.
How do I reset my Rainbird wireless controller?
You can reset the controller password while connected to the Rain Bird WiFi controller in AP hotspot mode. Press the button on the LNK WiFi Module in the controller for 1 second. The light should change from blinking green to blinking green and red.
Why is my sprinkler system not turning on?
If Sprinkler Zones Do Not Turn On When the sprinkler zones do not turn on at all, it is generally a problem with the electrical signals running from the controller to the valve solenoids. More rarely, it is caused by a faulty valve that needs to be rebuilt or replaced.
Why is my sprinkler system not working?
One of the most common problems is a clogged nozzle. Other times the nozzle may be irreversibly damaged, so a new one is needed. If cleaning or replacing the nozzle doesn’t fix the problem, the next place to look is at the actual head. In these cases, your sprinklers might drip water instead of spraying it.
Why don’t my sprinklers turn off?
One of the most common reasons that a sprinkler zone won’t shut off has to do with debris stuck in the valve. This is especially the case if your sprinkler heads are located underground. The soil, rocks, and loose debris that surrounds the system could potential tamper with the solenoid.
How do I manually open my sprinkler valves?
To open the valve manually, twist the manual bleed screw counter-clockwise until the valve opens. It usually doesn’t need to be more than one-half turn. To close the valve turn the manual bleed screw clockwise until the valve closes.
How do I turn off Irritrol valve?
The solenoid is also used to turn the watering zone on and off manually while standing at the valve. Grasp the body of the solenoid firmly and turn it counterclockwise at least a quarter turn. Turn the solenoid back the other way to shut off the water supply.
How do I adjust my Irritrol Pro Series?
Adjust flow rate by tightening or loosening the screw in the center of the sprinkler head when the system runs. Turning counterclockwise increases flow, and turning clockwise decreases flow. Opening this valve should restore full flow if the system works at full pressure.
How do you adjust finger sprinkler heads?
Grip the spray head between two fingers. Then, rotate it by hand so it is aimed at the direction you want the water to spray. For example, if you want the water to spray towards the right, rotate the head to the right. If you want the water to spray more to the left, rotate the head to the left.
Should solenoid be on or off?
Avoid over-turning the solenoid in either direction, as this can cause damage to the components or cause pressurised water to escape the solenoid. When you hear water rush through the device, it’s easy to tell that the valve has opened successfully.
Is Lawn Genie and Irritrol the same?
The DPR series are the same valves as the Lawn Genie model L701 & L703. The Irritrol APR model is a good choice for a residential system where a anti-siphon valve is appropriate (see below). These anti-siphon valves have a built in atmospheric backflow preventer.
How does a sprinkler controller work?
The stations send electrical impulses to their respective valves to open or shut them, letting water through to the sprinklers (or not). Because this works electronically, the controller has to be physically located near enough to the valves to allow for a wired hookup.
How do you test Rainbird rain sensor?
Testing the System Once installed, the completed system can be tested by turning on any controller irrigation zone, verifying that zone does come on, and then pressing down on the Rain Sensor pin located on the top of the dial cap. The irrigation system should stop watering within a few seconds.
How do I know if my Rainbird rain sensor is working?
The zone should shut off. (If your rain sensor does not have a button on top, it is not a cork-disc sensor) Release the button and the zone should come back on. If it does, the sensor is operating properly.
