Table of Contents
How to Hydro Dip STEP 1: CLEAN. Using 91% isopropyl alcohol, cleaning cloths and gloves, ensure that the work piece is clean. STEP 3: BASE COAT. Apply the base coat. STEP 2: PRIME. STEP 4: Film placement. STEP 5: FILM hydration. STEP 6: Tape. STEP 7: ACTIVATE & WAIT. STEP 8: DIP.
What materials do you need to Hydro dip?
Step-By-Step Guide to Hydro Dipping Large, deep plastic container (the container will have paint on the inside after the hydro dipping is complete) DIY complete hydrographic printing kit. Object to be dipped. Sandpaper to smooth the surface. Rags. Bucket of mild cleaning solution and water. Vinyl, rubber, or latex gloves.
Can I Hydro dip myself?
It’s the original (and patented) DIY hydro dipping kit. The process formally known as water transfer printing was once only available commercially. MyDipKit was designed for the everyday, do it yourself Hydro Dipping enthusiast. The kit contains the basic supplies needed for processing parts at home.
Do you Hydro dip with hot or cold water?
The ideal water temperature range for hydrographic dipping is 80 to 90 degrees Fahrenheit.
Do you need a base coat for hydro dipping?
Choosing the right base coat color is very important in hydro dipping. So if you are wanting the design to look as intended and usually shown on the product page of where you are purchasing the film, then using a white base coat is usually the best choice unless it is specified that another color was used in the photo.
Do you need activator to hydro dip?
Under and over activating are two of the leading causes in problems with hydro dipping. You are not applying a layer of paint, you just need enough activator (with a fine mist, fan pattern spray) to cover the film lightly.
Can you hydro dip without spray paint?
However, you’ll need to be more careful using the spray can because spraying too close can form air bubbles on the surface, leading to undesirable patterns. People would often ask, can you hydro dip without spray paint? Yes, you can.
Can u hydro dip glass?
These hydro dip glass bottles are colorful and unique and the paint technique is easy. You will never get the same paint finish twice with hydro dipping. I have photos, a tutorial, and a video showing the process. Definitely watch the video because the technique is so much easier to follow.
How expensive is hydro dipping?
Average Costs for Hydro Dipping The average cost for hydro dipping a wheel for a vehicle is roughly $150, and that pricing can vary by as much as 20% – 50%, depending on the type of activator, finish, and labor costs. Hydro dipping fees for guns typically range from $200 to $500, depending on the make and model.
How long does it take hydro dip to dry?
You’ll sometimes need to wait about two hours or more to apply the clear coat after dipping. If you’ve used a convection oven or another heat source to dry the item after hydro dipping, it may be ready for the clear coat in as little as 30 minutes.
How do you prevent air bubbles when Hydro dipping?
Putting your item flat into the paint allows air bubbles to form. To avoid this you want to lower your item on an angle so no air bubbles are able to be created and the paint sticks cleanly.
Can you use any primer for hydro dipping?
Any paint requires a good primer to stick to, and a clear coat to seal the paint in after and offer ultimate protection. Rust-Oleum Painter’s Touch Flat White Primer is the go-to for hydro dipping.
Do you let the primer dry before hydro dipping?
Next in the hydro dipping process you want to apply the primer. Onto the next step in your hydro dipping project. Wait for 15 minutes at 20 degrees c for the part to be fully dry before moving on to the next step.
How do you dry after hydro dipping?
Use a clear, spray sealant. To keep your hydro dip paint looking fresh and clean, spray it with a clear spray sealant (available in hardware stores in matte, semi-gloss, or gloss finish). Spray an even coat over the object and let it dry for several hours.
Do you clear coat after hydro dipping?
STEP 11: CLEAR COAT Clear coating is highly recommended for all hydrographically decorated parts. This helps to seal in the inks and allows for a cleaner finished product. When the dipped part is dry, apply the clear top coating (matte, semi-gloss or high gloss) to finish off your newly dipped hydrographic part.
What spray paint do you need for hydro dipping?
You can hydro dip any item with a nonporous surface — all you need are a few simple supplies! Step 1 – Using your 2x Rust-Oleum Spray Paint prime the item that you are going to Hydro Dip. Allow that to dry.
How permanent is hydro dipping?
Hydrographic finishes are very robust and will last for many years under normal use. However, similar to your car finish, the paint can scratch if the product is abused. Scratching the protective clear coat can cause failure to the hydrographic finish.
Can I Hydro dip my gun?
The pattern wraps around the surface of the gun. The gun may need to be dipped more than once to allow the entire surface to be coated.Hydro Dip or GunSkins? Hydro Dipping Gun Skins Permanent: Can be removed using professional bead blasting. Removable: Has no affect on the surface of the weapon.
What is the activator for hydro dipping?
INK DRINK FILM ACTIVATOR. INK DRINK Hydrographic Film Activator is an easy to use film activator, compatible with most films on the market. Ink Drink maintains the richness and color vibrancy of your film and activates most films with a single pass (one coat).
How long after base coat can I Hydro dip?
Simply placing it in a warm room is sufficient to make it looser and easier to be sprayed. Let the paint set in the room until you’re ready to use it, or for around twenty minutes, and then you’ll see the improved performance. Hydro dipping takes standard printing practices and adapts them to a variety of surfaces.
What tape is best for Hydro dipping?
SmartSolve Water Soluble Tape is revolutionary to the hydrographic industry and is used to mask off sections you want covered, making it the perfect solution for double-dipping.
