Table of Contents
If your chainsaw engine dies at full throttle, check the following parts: the carburetor, fuel lines, fuel filter, air filter, and muffler. This is particularly true when you attempt to run your chainsaw on full throttle. You may be able to purchase a carb kit, and clean and rebuild the carb, rather than replacing it.
Why does my Husqvarna chainsaw stall when I accelerate?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
Why does my chainsaw stall when I give it gas?
Carburetor Adjustment An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
Why does my Husqvarna chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
How do you adjust the carburetor on a Husqvarna chainsaw?
Tip Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw. Turn both the low- and high-speed screws clockwise to the midpoint. Adjust the low-idle screw clockwise and counterclockwise respectively, until you find the highest idling speed.
How do you adjust the idle speed on a Husqvarna chainsaw?
T Screw – Next, locate the T screw. This adjustment screw is responsible for adjusting the chainsaws idle. Begin by turning the T screw clockwise until the chainsaw chain begins to move. As soon as you notice it moving, turn the T screw counterclockwise slowly until the chainsaw chain stops.
How do I get my chainsaw to idle?
First set the idle speed by setting it as high as possible without engaging the clutch (close to 2700 RPM if you have a tachometer). Then set the low-speed screw by turning it gently in until the engine begins to starve for fuel, then turn it out gently until the engine loads up.
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
What does L and H mean on a carburetor?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).
Why does my chainsaw run then stop?
A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
How do I know if my chainsaw is running lean?
If your chainsaw is running lean, it will take a long time to return to idle once you rev it up at a high rpm. Idle means the chain isn’t spinning even though the engine is on. Also, the saw will work at a higher rpm than recommended, but it will have less cutting power due to the lack of gas in the mixture.
How often should you clean chainsaw air filter?
How do I clean my chainsaw air filter? Generally an air filter should be cleaned thoroughly on a daily basis after use. In more demanding conditions, the air filter should be checked and cleaned every time you re-fuel.
When should I change my chainsaw air filter?
You should replace the filter once per year if the chainsaw has had plenty of use. It will depend on the rate of use and the amount of dirt and debris the unit has had to contend with. The air filter will gradually degrade and wear out.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear. This reduces a chainsaw’s ability to cut accurately.
Do Husqvarna chainsaws have spark arrestors?
This spark arrestor (part number 545006056) is for chainsaws. Spark arrestor 545006056 attaches over the exhaust port of the muffler to prevent sparks from igniting dry leaves or grass. Let the engine cool before installing this part.
Should I remove spark arrestor?
You can safely remove the spark arrestor or even install an aftermarket exhaust system on many ATVs without having to make alterations to your jetting because they are normally set up to run a bit rich from the factory, but this is no general rule!.
