Table of Contents
TIP: To optimize plywood use, plan your shelving to be 12″, 16″ or 24″ in width. Then you can rip your plywood into either four 12″ wide strips, three 16″ wide strips or two 24″ wide strips with no waste.
How wide should I make garage shelves?
The dimension of shelf width is hotly debated, but we settled on a depth of 16 inches. It’s deep enough to support tool cases and standard boxes, but shallow enough as to not lose stuff in the back and have to reach to far.
What size plywood should I use for garage shelves?
We use 1/2″ plywood for the 16″ width shelving – perhaps go up to 5/8″ or 3/4″ if you do 24″ wide shelving or have especially heavy loads destined for these shelves.
What is the average depth of a storage shelf?
1. The shelves shouldn’t be too deep. The standard depth of most shelves is 16 to 20 inches deep. The highest shelf should be shallower, like 12 inches deep, to make those items easier to access.
How deep should a garage shelf be?
Garage shelves typically range from 12 – 24 inches deep.
What is the standard distance between shelves?
Average Shelf Spacing A good average spacing for shelves is between 8 and 12 inches. If you have oversize books to store, you might prefer to increase the spacing to 15 inches.
What thickness of plywood is best for shelves?
As a general rule, the heavier the items you will be placing on the shelves, the thicker the recommended product will need to be. The most common size used in shelving is a 3/4 inch thickness.
Is 1/2 inch plywood strong enough for shelves?
For everything else, like casework, shelves, slab doors, drawer fronts, and raised panels (done with edging with solid wood). In using 1/2″ for cabinet construction, it has the propensity to warp, and doesn’t lend itself to hold screws very well (because of the thickness).
What wood should I use for garage shelves?
By using hardwood plywood, you’ll make stunning garage shelves and cabinets without breaking the bank.
What is the best depth for pantry shelves?
Don’t go too deep. Most experts recommend that pantry shelves be no more than 12 inches deep. Any more, and things begin to get buried.
What size do shelves come in?
Board Sizing Standard Lumber Sizes BOARD SIZE ACTUAL SIZE SHELF HANGER WIDTH 1 X 6, 2 X 6 3/4 X 5-1/2, 1-1/2 X 5-1/2 5-1/2 [5-5/8 ACTUAL] 1 X 8, 2 X 8 3/4 X 7-1/4, 1-1/2 X 7-1/4 7-1/4 [7-3/8 ACTUAL] 1 X 10, 2 X 10 3/4 X 9-1/4, 1-1/2 X 9-1/4 9-1/4 [9-3/8 ACTUAL].
How high should storage shelves be?
Ideally, shelves should be 6” to 1′ off the floor to keep the items stored on them clean and dry. This also leaves the floor area for storage of bulky and heavy items such as shop vacuums and five-gallon containers. Enclosing the shelves within a cabinet or behind doors is a great help in keeping your items clean.
How many brackets do I need for a 36 inch shelf?
DETERMINE HOW MANY BRACKETS ARE NEEDED Of course, all shelves are different, but if your shelf is over 36” long, we suggest using more than 2 brackets.
How do you stagger 3 floating shelves?
When using three shelves, place the middle shelf higher or lower than the one on either side. Five shelves can be staggered with two or three higher than the others, alternating every other shelf for a horizontal grouping.
Is 12mm plywood OK for shelves?
It is generally unsuitable for shelving as the finish is poor. Use 12mm chipboard as a minimum and support the shelf at no greater than 300mm centres for all but the lightest of loads. Or 18mm chipboard with supports no greater than 700mm apart.
What kind of plywood do you use for shelves?
Tip. Plywood is the industry standard for shelving, so it’s a good choice for bookshelves.
How thick should Wood be for shelves?
Use 3/4-inch thick materials for shelves and bookcase structure. If you’re using hardwood solids, it’s OK to boost the thickness to 1 1/4 inch for almost unlimited support. This type of shelf looks more like a mantel and is expensive, but adds the opulent look of craftsmanship.
Can I use half inch plywood for shelves?
First shelf sections were put in back in 2008, no sign of sagging yet. They cost more than plywood, but I think ease of use and durability make it worth it. Adding 1x2s under the plywood will stiffen it up just fine.
Is half inch plywood strong?
The most common plywoods are 1/2-3/4” thick. These sizes are for anything from quick DIY projects to home structural uses. The thickest pieces of plywood are only 1” thick. Slim in the grand scheme of things, this plywood is strong enough to be used in industrial building projects.
Should I use half inch or 3/4 inch plywood?
In my experience building cabinets and drawers, 1/2 plywood only becomes useful for drawer sides, sometimes, bottoms, and cabinet backs. However, if you’re working on shelves, fronts, and panels, it would be best to use 3/4 plywood for better strength.
Is MDF strong enough for garage shelves?
Because it’s inexpensive and fairly durable, medium density fiberboard s a good choice for practical projects like shelving and storage cabinets. But MDF wood is great for decorative projects too. Over the past 15 years, I’ve used MDF to build everything from crude shelving in my shop to fancy trim in upscale homes.
How do you make a scrap shelf out of wood?
Building Your Scrap Wood Shelf Step 1: Start by cutting your boards to size. My boards measure 3 inches X 24 inches and 6 inches x 24 inches. Step 2: Glue boards together. Step 3: Clamp and screw. Step 1: Find your studs and center your shelf. Step 2: Level. Step 3: Drill your pilot holes. Step 4: Screw your shelf in place.
How do you make a wooden shelf bracket?
Instructions Cut a 2″ x 2″ board to 7.5″. Cut a second piece to 6″. Use a miter saw to cut the 1″x2″ board to 5.5″ long, with a 45-degree angle at each side to form a trapezoid. Sand any rough edges. Use wood glue and finishing nails to connect the three pieces to form the shelf bracket.
How do you stabilize free standing shelves?
Drill a hole for each foot in the underside of one of the legs and tap in the foot, using a hammer. Right the bookshelf and put it back into position. Raise or lower each foot until the bookcase stops wobbling. Raise the feet by turning them clockwise; lower them by turning them counterclockwise.
