Table of Contents
Deck boards are typically 12 or 16 feet long, roughly 5-½ inches wide and about an inch thick – though specific dimensions can depend on the style of board you choose. Composite decking can come with two bottom profiles.
How wide is a 5 4 deck board?
5/4 Decking Actual Dimensions 1″ x 5.5.” If you use 5/4 decking, you are getting two-thirds of the board of a 2×6.
What width are decking boards?
How wide are deck boards? The most common decking widths are 90mm to 150mm, with 120mm and 140mm in between.
What is the actual size of a decking board?
Lumber sizes are usually given in “nominal” measurements. The nominal measurements are a board’s size before it has been planed smooth (surfaced) on all 4 sides.Decking Planks. Nominal Size Actual Size 5/4 × 6 1″ × 5-1/2″ 6/4 × 6 1-5/16″ × 5-1/2″.
Can I use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
What is the actual width of a 2×8 board?
Lumber Dimensions: Nominal vs. Actual Nominal Size Actual Size 2×4 1-1/2″ x 3-1/2″ 2×6 1-1/2″ x 5-1/2″ 2×8 1-1/2″ x 7-1/4″ 2×10 1-1/2″ x 9-1/4″.
How wide is a 10 inch board?
Nominal vs. Actual Measurements of Dimension Lumber Nominal Size Actual Size 1 x 8 3/4 x 7 1/4 inches (19 x 184 mm) 1 x 10 3/4 x 9 1/4 inches (19 x 235 mm) 1 x 12 3/4 x 11 1/4 inches (19 x 286 mm) 2 x 2 1 1/2 x 1 1/2 inches (38 x 38 mm).
Are wider deck boards better?
Narrower boards work best. 4” nominal (3-1/2” actual) wide deck boards perform better than wider (6” nominal) deck boards. Because there are more gaps between the deck boards, 4” nominal deck boards provide about 44% more top of deck ventilation than 6” nominal decking.
How thick is a deck board?
NOTE: Standard boards are often called a 5/4 board when referring to traditional lumber, which means the actual thickness is typically somewhere between 1” and 1 ¼”. Thicker boards are often called a 2 x 6 when referring to traditional lumber, which means the actual thickness is somewhere between 1.2” and 1.5”.
How many deck boards do I need for a 12×12 deck?
For example, a 12-foot x 12-foot deck of 5/4 x 6 pressure treated wood decking on 16 inches on center spacing of joists will require: A 12-foot long deck with joists 16 inches on center will require 10 joists. 20 fasteners x 26 (number of rows of decking) = 520 fasteners. Add 10 percent to be safe.
Why do they call it 5 4 decking?
Quarters refer to the thickness of rough-sawn lumber measured in ¼-inch increments. Instead of reading it as a fraction, it should be read as a number of quarters: 5/4 is five quarters, 4/4 is four quarters, etc.
How far do I space deck boards?
Proper wood deck board spacing should have at least a 1/8 inch gap after the decking has dried out. If you install your wood or treated deck boards while they are still wet boards, then they should be attached without a gap between them.
Should you leave a gap between deck boards?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink.
Is it better to use 2×6 or 2×8 for deck?
For upper-level decks, 2×10 is recommended as the minimum size to use for strong guard post connections. 2×6 joists should only be used on ground-level decks that do not require, and will not provide for, any guards. Most decking is not strong enough to support longer spans than 16″.
Can you use 1×6 for deck boards?
Width of material: We recommend only 1×4, 5/4×4 or narrower boards. Never use 1×6 or 5/4×6 material in close to ground applications. Spacing between boards: You must allow space for your deck boards to expand when they take on moisture, as they will inevitably do when exposed to wet weather, rain or high humidity.
How wide is 1×6 board?
A 1×6, for example, actually measures 3/4″ x 5 1/2″. In this case, the planing is necessary for a smoother surface, so that the board could be used for interior applications.
How wide is 1×4?
A 1×4 measures 3/4 inch thick by 3 1/2 inches wide and a 2×4 measures 1 1/2 inch thick by 3 1/2 inches wide.
Why are lumber dimensions off?
The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.
What is the actual size of a 1×10 board?
1x Board Sizes The larger 1x boards (1×8, 1×10, etc.) lose 3/4 inch in width. That means a 1×10 is actually 3/4 inch in thickness by 9 1/4 inches.
How long is a 12 foot board?
Softwood Lumber Lengths Length in Feet Length in Inches Length in Meters 6 feet 72 inches 1.829 meters 8 feet 96 inches 2.438 meters 10 feet 120 inches 3.048 meters 12 feet 144 inches 3.658 meters.
What is a 5 4 inch board?
5/4 means approximately 1-1/4″ thick. 6/4 means approximately 1-1/2″ thick. 8/4 means approximately 2″ thick.
