Table of Contents
5/4 Decking Actual Dimensions 1″ x 5.5.” If you use 5/4 decking, you are getting two-thirds of the board of a 2×6.
How wide is a decking board?
Deck boards are typically 12 or 16 feet long, roughly 5-½ inches wide and about an inch thick – though specific dimensions can depend on the style of board you choose.
What is a 5 4 inch board?
5/4 means approximately 1-1/4″ thick. 6/4 means approximately 1-1/2″ thick. 8/4 means approximately 2″ thick.
What is the actual thickness of 5/4 lumber?
5/4 (five-quarter) lumber is 1.25″ thick when rough sawn. When 5/4 lumber is planed, typically it is finished at 1.063″ thick. 6/4 (six-quarter) lumber is 1.5″ thick when rough sawn.
What is the most common deck board size?
The most common or standard deck board width is 6-inch wide planks based on square-foot coverage, labor, and material cost.
What size board should I use for a deck?
Width: Six-inch wide boards are ideal in most cases. Four inch wide material takes longer to install, creates more gaps and requires a lot more fasteners—but you can use it. Eight inch wide boards, because of their greater width, have more of a tendency to crack and cup; avoid using them.
Is 5 4 an inch and a quarter?
The Actual Size of 5/4 Lumber A board foot is roughly equivalent to 144 cubic inches. However, hardwoods can also be sold in quarters, and ¼ inch of thickness is equivalent to one quarter. Following these rules, a 5/4 board is 1¼ inches thick. Pro Tip: The thickness of a hardwood board is measured before surfacing!.
What type of wood is 5 4?
It simply refers to how many 1/4-inches thick the rough stock is. For example, 4/4 (read out loud as four-quarters) is 1-in. thick in the rough. 5/4 is 1-1/4-in.
What are the dimensions of 4 4 lumber?
A board foot is 12″ X 12″ X 1″. A “quarter” system is commonly used in the hardwood lumber industry when referring to thickness. 4/4 refers to a 1 inch thick board, 6/4 is 1-1/2 inch, 8/4 is 2 inches, and so on.
How far can 5 4 decking span?
Decking Board Considerations Decking boards span from joist to joist. If you use 5/4 decking, joists must be no farther apart than 16 inches. Decking made of 2x4s or 2x6s can span up to 24 inches. If you will run decking at an angle, you might need to put the joists closer together.
How wide is a 12 inch board?
Nominal vs. Actual Measurements of Dimension Lumber Nominal Size Actual Size 2 x 8 1 1/2 x 7 1/4 inches (38 x 184 mm) 2 x 10 1 1/2 x 9 1/4 inches (38 x 235 mm) 2 x 12 1 1/2 x 11 1/4 inches (38 x 286 mm) 4 x 4 3 1/2 x 3 1/2 inches (89 x 89 mm).
Can I use 2×6 for deck boards?
Wood decking is commonly available in 2×6 and 5/4 x 6 profiles. 5/4 x 6 is produced specifically for decking and is milled with a radius edge or bull nose. 2×6 is thicker and is stronger, but is also more expensive. Spacing between deck boards provide a few critical functions.
Should deck boards have a gap?
When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.
How wide is Trex deck board?
The boards are 0.75 inches thick and 11.375 inches wide. The Grooved Edge board is 1 inch thick and 5.5 inches wide. It is available in 12, 16 or 20 foot lengths.
How wide is 2×8?
Lumber Dimensions: Nominal vs. Actual Nominal Size Actual Size 2×6 1-1/2″ x 5-1/2″ 2×8 1-1/2″ x 7-1/4″ 2×10 1-1/2″ x 9-1/4″ 2×12 1-1/2″ x 11-1/4″.
How far apart should deck boards be spaced?
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink.
How thick should decking boards be?
Most composite brands have the same thickness, but softwoods and hardwoods will range from 1″ to 2″ thick for decking. Softwoods should be at least 1 1/4 inches thick for a 16″ on center span. 2 inches thick will allow for a 24″ on center span.
Can I use 2×8 for deck boards?
Q: Can I use 2×8 treated lumber as deck boards? A: No, that’s a not a good idea. Lumber wider than 6 inches should not be used as a flat surface. Wide, flat boards have a tendency to pool rain water, which can lead to cupping problems.
