Table of Contents
How do you wire a motor for a trolling motor?
24-Volt Wiring Loosen the two terminals on the circuit breaker supplied with the trolling motor. Slide the red wire from the motor over one of the terminals and tighten it down. Loosen the positive terminal on the second battery. Slide the red wire over the positive terminal on the second battery and tighten it down.
How do I know if my trolling motor is 12 or 24 volt?
The nameplates are most often found in the foot petals of the motor. Otherwise, you can look at the configuration of the trolling motor batteries to find the volts. Open the hood and look at the battery. If you see 6 cells, it’s a 12-volt battery, but if you see 12 cells, it means it’s a 24-volt battery.
What gauge wire is on a Minn Kota trolling motor?
CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE MOTOR THRUST/MODEL MAX AMP DRAW WIRE EXTENSION LENGTH 5 FT 30 lb. 30 10 AWG 40 lb., 45 lb. 42 10 AWG 50 lb., 55 lb. 50 8 AWG.
How many amps does a Minn Kota trolling motor use?
While the Minn Kota Endura C2 30 Freshwater Transom Mounted Trolling Motor (30″ Shaft) model takes 32 amps/hr to get that 30 lbs of thrust, this one can do 30 lbs of thrust for roughly 18 amps/hr.
What size wire is needed for a 36 volt trolling motor?
You need the 6 gauge.
Why does my trolling motor have 3 wires?
The three wire plug is for a 12/24V system. On a 12/24 you have a 12V hot, 24V hot, and a ground.
Can you connect trolling motor directly to battery?
Connect the 12-volt trolling motors to a single 12-volt battery by simply fastening the black negative lead from the motor to the negative battery terminal, and the red positive lead from the trolling motor to the positive battery terminal. Include a 50-amp circuit breaker on the positive connection.
What voltage is my Minn Kota trolling motor?
A Minn Kota trolling motor will operate with any lead acid, deep cycle marine 12-volt battery/batteries.
What kind of wire do you use for a trolling motor?
Many trolling motors can be used with 8 gauge wire, however, the length of wire you need and the amperage of your motor can alter the size of wire you need. For example, if you need a longer length of wire, you’ll likely need a lower gauge and therefore thicker wire.
How long will battery run trolling motor?
Almost 5 hours doesn’t seem too bad, but that is really a max runtime in ideal conditions. Reality is likely to be less. If the battery is old, damaged or not fully charged then you will not get the rated amp hours from it, reducing your runtime. Significant cold or hot weather will also reduce your runtime.
Will a 24v trolling motor run longer than a 12v?
The 24 volt has more power usually and lasts longer in the wind than the 12 volt. The disadvantage to 24 volt is the price and the extra weight.
How many amp hours do I need for a 24 volt trolling motor?
The Force trolling motor can run on 24 volts or 36 volts, and the chart below shows how a 24v setting will draw higher amps then running at 36 volts.24 Volt Power Source. Throttle Level Thrust Current 10% 25 N-m (6 lbf) 2 A 20% 45 N-m (10 lbf) 3 A 30% 70 N-m (16 lbf) 6 A 40% 101 N-m (23 lbf) 9 A.
What size circuit breaker do you need for a 24 volt trolling motor?
All 12, 24 and 36 volt trolling motor systems (Minn Kota 70lb thrust motors should use a 50 amp breaker).
What happens if you run a 12 volt trolling motor on 24 volts?
The motor was designed for 12 volts and was designed to dissipate the heat from 12 volt power. When run at 24 volts the coils will heat up much faster than at 12 volts, and the motor will not be able to release the heat quickly enough.
What size battery do I need for a 55 lb thrust trolling motor?
For a 55 lb thrust in a trolling motor, you will at least need the battery size of 240Ah rating. Depending on the speed, you will be using approximately 20-40 amps.
Where is the model number on a Minn Kota?
The serial number is located on the top of the transom bracket.
What gauge is 24 volt wire?
If you have a 24V supply for a 200 amp device, we will assume that the wiring is copper and has a typical insulation and installation type. With a wire distance of 25 feet and a voltage drop of 3%, you will need a wire size of 4/0 AWG.
Is 8 gauge wire enough for 36V trolling motor?
8 awg will work. Depending on what you’re putting it on and the length of wire on whether 6 or 8 is needed. Personally, if the wire run is over 30′ (that’s from the negative connection of battery 1 to the positive connection of battery 3 in the case of 36V) I would go with 6ga.
Why does my trolling motor have 4 wires?
To make charging easier, the 4 prong/4 wire system became standard on several bassboats. This, in effect, moved the 4 battery post up to the boat side of the plug and configured them in such a way as the two negatives were side by side and the two positives were side by side.
What is the orange wire for on my trolling motor?
The orange wire is for the +24Volt connection. So, back on the batteries, the black wire is connected to the – terminal of battery #2. The red wire is wired to the + terminal of battery #2.
