Table of Contents
Just hook up the XBee module to the Explorer board and plug it with the laptop using USB cable. If you don’t have any converter or explorer board, then an Arduino board can be used as a USB to serial device which can easily communicate with the XBee and laptop.
How do I connect XBee to Arduino Uno?
Connect VCC (pin 1) of XBee module to 3.3V of Arduino Nano and GND (pin 10) of XBee to GND of Arduino Nano. These two connections make up for powering the transmitting side XBee module. Connect Dout (pin 2) to D2 of Arduino Nano and Din (pin 3) to D3 of Arduino Nano.
How do I connect XBee to Arduino Proteus?
Schematics Proteus Circuit Diagram. Download. Gnd Xbee – Gnd Arduino. Assembling Hardware. Download. Installing X-CTU. Download. https://www.digi.com/resources/documentation/digidocs/90001526/tasks/t_download_and_install_xctu.htm. Add Your Xbee. Download. The configuration of your XBee. Download. After Uploading The Code. Download.
What is XBee Arduino?
Overview. The Xbee shield allows an Arduino board to communicate wirelessly using Zigbee. It is based on the Xbee module from MaxStream. The module can communicate up to 100 feet indoors or 300 feet outdoors (with line-of-sight). The shields breaks out each of the Xbee’s pins to a through-hole solder pad.
How do I set up XBee?
Step 1: Download X-CTU Software. The X-CTU software is free to download and provides a simple interface to configure and update your XBee transceivers. Step 2: Put together your XBee breakout board. Step 3: Configure 1st XBee as a coordinator. Step 4: Configure 2nd XBee as Router. Step 5: Test the configuration.
How do I use XBee in Explorer?
Plug the unit into the XBee Explorer, attach a mini USB cable, and you will have direct access to the serial and programming pins on the XBee unit. The highlight of this board is an FT231X USB-to-Serial converter. That’s what translates data between your computer and the XBee.
How do I use XBee USB adapter?
Simply plug the XBee 3 USB Adapter into the USB port of a laptop or PC for instant access to an Digi XBee network and its connected devices. This compact, USB-powered wireless adapter enables local network configuration, diagnostics or device monitoring. The XBee 3 USB Adapter can be programmed with Zigbee, 802.15.
What is XBee used for?
XBee is a module produced by Digi International mainly use as a radio communication transceiver and receiver. It is mesh communication protocols that sits on top of IEEE 802.15. 4 ZigBee standard. XBee supports peer-to-peer as well as point to multi-point network communications wirelessly with the speed of 250 kbits/s.
What is XCTU?
XCTU is a free multi-platform application designed to enable developers to interact with Digi RF modules through a simple-to-use graphical interface. It includes new tools that make it easy to set-up, configure and test XBee® RF modules.
What is the difference between XBee and Zigbee?
XBee is a family of radio modules and is a registered trademark of Digi International. Zigbee is a wireless communications protocol and a registered trademark of the Zigbee Alliance. Many people confuse these two names because both are involved in radio networking and have “Bee” in their branding.
How do you code XBee?
Connect the ground and 3.3V from the Arduino to the ground and power rails of your breadboard. Connect the power and ground rails of the breadboard to the 3.3V and GND pins on your Explorer module. Next, connect the XBee Explorer pin OUT to Arduino pin 2 (RX), and XBee pin IN to Arduino pin 3 (TX).
How do I use Arduino WiFi module?
Follow these steps. connect the red wire to VIN(3.3V) to the +3.3V power from the microcontroller. connect the black wire to the ground. connect the green wire to the TX of the Wifi module and microcontroller. connect the yellow wite to the RX of the wifi module and microcontroller.
How do I use XCTU software?
Launch XCTU. Click the Configuration working modes button . Click the Discover radio modules button .Optional: Add a radio module Click the Add a radio module specifying the port settings button . In the Add radio device dialog, select the COM port for the device you want to add. Click Finish.
How do I know if XBee is working?
Range test Check cables. The USB cables should be firmly and fully attached to both the computer and the XBee development board. Check that the XBee module is fully seated in the XBee Grove Development Board. Check the XBee module orientation. Check that the XBee modules are in the same network. Restore default settings.
Can XBee transmit and receive at the same time?
1 Answer. Yes, it is possible to send and receive data at the same time. When XBee modules are configured in “AT mode” (also referred to as “Transparent Serial”), you configure the DH and DL parameters to identify the destination node that will receive the serial data.
How do I transfer data from Arduino to XBee?
For this, connect one end of the button to D5 of Arduino and the other end of the button to GND. Connect VCC (pin 1) of XBee module to 3.3V of Arduino Nano and GND (pin 10) of XBee to GND of Arduino Nano. These two connections make up for powering the transmitting side XBee module.
What is XBee Explorer?
This is the SparkFun XBee Explorer Dongle unit for the Digi XBee module line. With the XBee Explorer Dongle you can plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee.
What is XBee Explorer dongle?
This XBee Explorer dongle features an FT231X USB-to-Serial converter that translates the data between the computer and the XBee. The dongle offers a reset button, a voltage regulator for power supply, and four LEDs (RX, TX, RSSI, and power indicator) to help debug the XBee.
