Table of Contents
Apply a liberal amount of Wipe-On Poly to a clean, soft, lint-free cloth and rub it into the wood. Let dry 2-3 hours. Then lightly sand entire surface with fine sandpaper (220 grit) to ensure an even finish and proper adhesion.
How do I get a smooth finish with Wipe on Poly?
Wash it first with dish soap and water, then lightly sand the old finish with 220-grit sandpaper. Vacuum off the dust, then apply the finish as usual. Apply at least two coats to achieve an even sheen.
How many coats of wipe on polyurethane should I use?
As a rule, it takes three coats of wipe-on to match the buildup that you get from one coat of brush-on poly. That said, the speed of wipe-on application often makes up for those extra coats.
Is it better to brush or wipe polyurethane?
What is the benefit of using wipe-on Poly versus regular polyurethane? Wipe-on Poly is easier to apply than traditional or brush-on polyurethane. You can use it in cracks, crevices, and other difficult-to-reach areas. Wipe-on Poly also doesn’t leave brush marks, so you don’t have to sand as aggressively between coats.
What kind of rag do you use for Wipe-On Poly?
Here’s what I use when I apply wipe on poly to a finished piece of furniture: Minwax clear gloss wipe on poly. Minwax satin finish wipe on poly. White, lint-free cotton rags.
Can you apply polyurethane with a rag?
Polyurethane is so durable and water-resistant, it has largely replaced shellac and varnish as a wood finish. Originally, it had to be brushed on, but different formulations mean it can now be applied as a spray or by wiping it on with a rag.
Do you wipe off polyurethane?
Wipe the polyurethane varnish — directly from the can — onto the wooden surface, using a piece of cloth. Apply it in the same direction as the woodgrain to avoid streaks, then wipe off the excess with a clean cloth. Wipe off less varnish on the wood’s surface for a thicker finish.
Why does my polyurethane look streaky?
Bruce Wedlock replies: Brush streaks come from the finish not smoothing out after the application. The pad is just replacing the brush as the applicator. The first coat seals the wood and needs to be sanded lightly with 150 grit. The second coat might need light sanding with 180 before the third coat.
Should I sand after first coat of polyurethane?
Sand the dried and cured first coat of polyurethane no sooner than 24 hours after applying it. Use a very fine-grit abrasive, sanding with the grain of the wood.
How long to wait between Wipe-On Poly coats?
How Long to Wait Between Coats While Applying Wipe On Poly? It’s recommended that you wait for at least two to three hours before applying the next coat of wipe on poly.
How long should polyurethane dry between coats?
If you use water-based polyurethane, you only have to wait between 2 to 4 hours before applying the next coat. However, when using oil-based polyurethane, you might wait for 10 to 24 hours. You can apply the next coat in as little as 4 hours if you are using fast-drying, oil-based polyurethane.
Is wipe on polyurethane good for table tops?
Best for Small Tables–Minwax 60910000 Wipe-On Poly It is arguably the best polyurethane for small table tops, where a brush might be too slow or a pad might be too big. This high-quality polyurethane finish will protect your wood table and other furniture from water, stains, household chemicals, scuffs, and scratches.
Can you apply Minwax polyurethane with a rag?
Ease of application: Some Minwax® clear finishes can be easily applied with a cloth—no need to worry about drips or brush marks. Some dry very quickly and can be cleaned up with soap and water, while others require mineral spirits.
Does Wipe-On Poly yellow?
The Best Non-Yellowing Water-Based Polyurethane It’s easy to use, dries within a few hours, can be applied multiple times within 24 hours, dries completely clear, and doesn’t yellow over time.
Can you wipe on Minwax Fast Drying polyurethane?
Just keep adding to the ball and keep wiping. Twist the cover to squeeze the ball and let more poly out. I also always sand with 320 grits between coats. Don’t over-wipe it, keep a good wet coat on it and let it flow out.
How do you make a water based wipe on polyurethane?
For water borne polyurethane I use tap water or distilled water (never well water) as my thinning agent. To make your own wipe on polyurethane I recommend thinning to 50/50. One part polyurethane to one part thinning agent.
Can you polish wipe on polyurethane?
Add a pea-sized amount of car paste wax to a polishing pad or cloth. Work in short, smooth motions until there are no visible scratches in the polyurethane. Move the pad in smooth, horizontal motions so you can apply an even coat of wax to the surface. You can also use a section of 0000 steel wool to buff the surface.
