How To Use Wipe On Poly

How do I get a smooth finish with Wipe on Poly?

Wash it first with dish soap and water, then lightly sand the old finish with 220-grit sandpaper. Vacuum off the dust, then apply the finish as usual. Apply at least two coats to achieve an even sheen.

How do you wipe on polyurethane?

A margarine or cottage cheese tub is just right for wipe-on. Dip your rag into the finish, squeeze out the excess and wipe on. With the lid in place, the poly will remain fresh for a couple days. After a few days, the solvent will begin to degrade the plastic, so don’t use plastic for long-term storage.

What kind of rag do you use for Wipe-On Poly?

Here’s what I use when I apply wipe on poly to a finished piece of furniture: Minwax clear gloss wipe on poly. Minwax satin finish wipe on poly. White, lint-free cotton rags.

Can you apply Poly with a rag?

Polyurethane is so durable and water-resistant, it has largely replaced shellac and varnish as a wood finish. Originally, it had to be brushed on, but different formulations mean it can now be applied as a spray or by wiping it on with a rag.

Does Wipe-On Poly yellow?

The Best Non-Yellowing Water-Based Polyurethane It’s easy to use, dries within a few hours, can be applied multiple times within 24 hours, dries completely clear, and doesn’t yellow over time.

How long does Wipe-On Poly take to cure?

Wipe-On Poly will dry to the touch in 2-4 hours, to handle in 8-12 hours and can be recoated in 4-6 hours. Full cure will be achieved in 24 hours. Use paint thinner or mineral spirits.

Is Wipe-On Poly Food Safe?

According to finishing expert Bob Flexner, all finishes are food-safe once they have cured. Polyurethane varnish does not present any known hazard. However, no finish is food safe until it has fully cured. The rule of thumb for full curing is 30 days at room temperature (65- to 75- degrees F).

How do you make a water based wipe on polyurethane?

For water borne polyurethane I use tap water or distilled water (never well water) as my thinning agent. To make your own wipe on polyurethane I recommend thinning to 50/50. One part polyurethane to one part thinning agent.

Should I sand after first coat of polyurethane?

Sand the dried and cured first coat of polyurethane no sooner than 24 hours after applying it. Use a very fine-grit abrasive, sanding with the grain of the wood.

Can you wipe on Minwax Fast Drying polyurethane?

Just keep adding to the ball and keep wiping. Twist the cover to squeeze the ball and let more poly out. I also always sand with 320 grits between coats. Don’t over-wipe it, keep a good wet coat on it and let it flow out.

Why does my polyurethane have streaks?

Bruce Wedlock replies: Brush streaks come from the finish not smoothing out after the application. Viscous finishes like typical oil varnishes don’t flow easily, so brush marks can result. One solution is to thin the finish so it flows evenly before it tacks up.

Can you apply Minwax polyurethane with a rag?

Ease of application: Some Minwax® clear finishes can be easily applied with a cloth—no need to worry about drips or brush marks. Some dry very quickly and can be cleaned up with soap and water, while others require mineral spirits.

Does Wipe-On Poly penetrate wood?

Yes, you can use wipe on poly over stain. Wipe on poly is an excellent paint to protect your unfinished wood. But be sure to allow the stained wood to dry thoroughly before top coating with the wipe on poly.

Should I apply polyurethane with a rag or brush?

Apply the first coat of polyurethane using the best technique for the surface. Brush flat surfaces with a thin coat using a bristle brush. Wipe contoured surfaces with a clean cloth, going with the grain. Brushing a rounded, contoured or vertical surface is more likely to create drips.

How long between coats of wipe on poly?

Allow Minwax® Wipe-On Poly to dry 2-3 hours before applying the next coat. If a third coat is desired, repeat the same procedure.

Is Minwax Wipe on Poly oil or water based?

Water Based Wipe-On Poly is easily applied with a cloth, without any drips or brush marks. It is the perfect choice for furniture, interior doors, trim and other woodwork. Because it’s water based it dries quickly and cleans up easily with warm water.

What clear coat will not yellow?

For clear coats that are not yellowing, Minwax’s Polycrylic is the best choice. Using it does not yellow over time, applies thoroughly and dries in a few hours, and does not need to be applied more than once once.4 days ago.

Can you Poly in the cold?

In colder temperatures, polyurethane tends to dry more slowly, which can cause a whitish film to develop.

Is Minwax Wipe on Poly waterproof?

In Chris Minick’s article on wipe on finishes, the table suggest that Minwax Wipe-On Poly has excellent waterproof characteristics. Jun 9, 2007.

Does Wipe-On Poly smell?

The water-base poly finish has almost no odor, and it also dries much faster. The smell is about the same as latex paint.