Table of Contents
How to Operate a Gas Fireplace Look over the user manual included with your fireplace. Remove your fireplace’s outer cover. Put a fireplace key into the device’s gas valve knob. Hold a long lighter up to the burner and ignite it. Turn the gas key. Replace the fireplace’s outer cover immediately.
What do you put under gas logs?
Supplies Needed To Freshen Up Your Gas Fireplace Silica Sand (not needed for a propane fireplace) Vermiculite (optional for natural gas fireplace) Rock Wool. Platinum Embers (optional for more dimension) Lava Rock.
Do you have to open the flue with gas logs?
One caution, though: Fireplaces with installed gas logs are required to have the damper open at all times. That’s either because a pilot light is constantly burning under the logs or because the homeowner might forget to open the damper when he or she turns on the fire.
What is the air shutter on a gas fireplace?
Air shutter adjustment – The correct fuel-air mixture in your Flare Fireplace produces blue base flame with yellow tips, with minimal soot buildup. The Fuel-air mixture can be set by the installer using the air shutter adjustment. Air shutter adjustment can be done from outside the fireplace.
Do I need a hearth for a gas fireplace?
Gas fireplaces are considered gas appliances, not true fireplaces. Some gas fireplaces are built with “zero-clearance” fireboxes, meaning you can put combustible materials right up to the sides, front and bottom. Not all gas fireplaces are zero-clearance, however, and some may require a hearth.
How long can you run gas fireplace?
In general, you should not run an unvented fireplace for more than three hours at a time. If you are using natural gas, you can usually run your fireplace for up to four hours before needing to refuel. If you are using propane, the limit is typically two hours.
Do gas logs heat a room?
Gas fireplaces rely on consistent combustion to produce real flames and keep the fire burning for long periods of time. Overall, gas fireplaces are highly efficient when it comes to heating a room. Once a fire has been burning for some time, it’s likely to heat a room rather quickly.
Do I have vented or ventless gas logs?
Follow the gas line from beneath the logs to where it disappears in the wall or floor. If the gas is merely contained by a simple gas line, then the logs are vent free. If there is a small cylinder attached to the gas line, then the logs are vent-free.
Do you open the damper on a gas fireplace?
The damper in a gas fireplace should remain open all the time. The glass between the firebox and your home prevents cold or heat from coming down the chimney and by leaving the damper open at all times, you eliminate the risk of having gas build up or backdraft into your home.
Why are my gas fireplace logs turning black?
Soot buildup is commonly caused by clogged burner ports and improperly positioned fire-logs. A fire-log that’s out of position can obstruct the flame path that ensures the clean-burning of gas. This contributes to soot formation on the fireplace. If this happens, you’ll need to clean off the fire-logs and doors.
How can I make my gas logs more realistic?
Use vermiculite instead. You can find rock wool, silica sand, vermiculite and crackling ash granules at a fireplace supply store or order online. You may need to turn the fireplace off and shift the rock wool around until it resembles a realistic pile of embers.
What are the fake logs in a gas fireplace made of?
A: Most gas logs are made from a ceramic fiber or refractory cement mixture designed to withstand high temperatures. Sometimes steel reinforcement bars are added to the inside of the logs to increase their strength and to prevent them from bending or cracking under extreme heat.
Do gas fireplaces stay lit?
Most gas fireplaces rely on a “continuous pilot light,” a type of pilot that remains lit so long as gas is flowing to the unit. Some newer, more energy-efficient models rely on an electronic ignition that only lights the pilot when the fireplace itself is turned on.
How do you start a gas fireplace with a lighter?
Flame-Lit Pilot Light Light a match or butane candle lighter and hold it near the burner in the fireplace. Turn the gas key to release gas to the burner. Pull the match or light away when the burner lights. You can adjust the flame height by turning the gas key.
Should pilot light always be on fireplace?
We recommend that you turn off your gas fireplace pilot light seasonally. Turning off your gas fireplace’s pilot light can save a substantial amount of energy and money. It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”.
How do I keep the air out of my gas fireplace?
One way to help minimize the draft is to install glass doors on the front of your fireplace opening. These glass doors will still radiate heat throughout the room, but will not allow the open flue to let in the cold draft. Another great solution for preventing these drafts is to install a direct vent gas insert.
How do you get air out of gas fireplace?
While pressing the valve control knob in, press the igniter button repeatedly until the pilot ignites. This could take anywhere from one to 10 minutes to bleed air out of the lines as the gas starts to flow. Once the pilot is lit, continue to press the valve knob inward for 30 seconds before releasing it.
What should a gas fireplace flame look like?
A gas fireplace should burn flames that are blue, perhaps with very small tips in yellow or orange. The flames should be steady and consistent no matter what. When you first turn on your fireplace, it’s okay if the flames start out a little unusual, as they may have a little less oxygen, fuel and air as they start up.
