Table of Contents
How does fanimation fan remote work?
Turn fan power on, press and hold SET button with a ball-pen or similar object on back of remote for 5 seconds within 60 seconds of powering fan in order to synchronize with fan motor. Step 2 Speed setting: After setting the transmitter learning, press the highest speed setting to set the rotational speed.
Why is my fan remote not working?
Perhaps the most common cause for a ceiling fan remotes not working is either a lack of batteries or dead batteries. If your remote control has an indicator light, check to see if it comes on. If necessary, place fresh batteries in the remote control, close the cover and test the control.
How do you change the code on a fanimation remote?
To set the code on receiver unit, slide dip switches to the same positions as set on the remote. To set the remote code with a small screwdriver or ball point pen (neither included), slide dip switches firmly up or down to same as receiver unit.
Are fanimation remotes universal?
These Fanimation controls are almost universal for all Fanimation fans, but be sure to double check as some fans have their own remote designed especially for them. Fanimation controls come in two different colors, white and light almond, as well as several shapes and sizes for the preference of a consumer.
How do I reset my fan remote?
There are several ways to reset a ceiling fan remote, but here’s the most straightforward: With the power off, hold down the button until the light on the remote flashes. Then, press and hold it again for 15-30 seconds to resynchronize the remote with your fan.
How do you put a fanimation fan in learn mode?
When you are sure power is off to the fan, turn the power back on. Your fan will go into learning mode for 30 seconds once it is powered back on. learn button. If your Fanimation ceiling fan successfully paired with your fanSync DC control, the fan should start spinning.
How do you hardwire a ceiling fan remote?
To hardwire your ceiling fan you will need to connect the fan’s power supply to the hard-wiring in your ceiling. This will enable the fan to function via a wall switch. In most instances, the wires inside of a power box are color-coded. Look at the wires attached to the fan and the wires in your ceiling.
Where does the red wire go on a ceiling fan with remote?
Connect the red wire from the ceiling to the black wire in the fan. Cap off the black and white wire from the output side of the remote receiver module. So the white wire on the receiver is capped? @user38908 The blue (or black depending on how you want it) coming out if the remote module would be capped.
How do you install a remote control light?
This guide will teach you how to install a remote control light switch in five easy steps. Step 1: Turn the power off. Turn off the breaker to any light switch where you plan to install a remote lighting system. Step 2: Wire the Switch. Step 3: Mount the Receiver. Step 4: Program the remote. Step 5: Test the remote.
Why is my fanimation fan beeping?
Answer: The fan will beep once when the timer is finished. This is just a notification or reminder that the fan is shutting off.
How do you turn off the remote on a ceiling fan?
Ceiling fans often have a pull cord or chain. You can use that to turn the fan on and off. Typically there is also a wall switch. But if you have a unit that has both a light and a fan the wall switch will usually turn off both of them.
Are fanimation fans good quality?
Fanimation is a leader in eye-catching ceiling fan designs that utilize the latest technology for unparalleled performance. One of their largest ceiling fans, the Fanimation Odyn is a 84-inch behemoth that uses 70% less energy than a regular ceiling fan thanks to it’s energy-saving DC motor.
Who makes fanimation?
Tom Frampton began his ceiling fan career in 1973, working under Burton A. Burton of Casablanca Fans. In 1984, Frampton started his own ceiling fan company, Fanimation, working out of his garage in Pasadena until demand for his product outgrew the space.
Why is my ceiling fan and light not working?
If the fan and lights don’t work, check that you are getting power to your room. Step 2: Check the breaker for your room to make sure your ceiling fan is getting power. Reset the breaker and test your fan and ceiling fan lights. Step 3: Replace one or all of the bulbs.
How do I unpair my Crompton fan remote?
First, you start by turning the fan off using its remote control. Then, you’ll need to wait; some brands ask to wait 15 seconds, though others may require as long as 30 seconds. Last comes the most critical step: in order to reset remote, press and hold the OFF button for about 10 seconds.
What does D and CFL mean on fan remote?
Ensure the “D/CFL” button in the battery compartment is set to the “D” position and the bulbs are incandescent or other dimmable bulbs.
How do I connect my fanimation fan to my phone?
fanSync is universal and works with most brands of 3-speed AC ceiling fans. Easily wire and install the fanSync receiver into your ceiling fan’s hanger bracket/canopy. Download the fanSync app to your smart device from Google Play or the App Store. Easily find and set up your fan(s) in the fanSync app.
