Table of Contents
What is ARDEX FEATHER FINISH used for?
ARDEX FEATHER FINISH® is an underlayment formulated from a blend of Portland cement and other hydraulic cements that provides a smooth, permanent finish for a variety of substrates prior to the installation of today’s demanding floor coverings, including sheet vinyl and VCT (vinyl composition tile).
Can you sand ARDEX FEATHER FINISH?
The final coat when dry should be sanded as smooth as possible before putting on color or sealant. I would allow 1 day between coats. Ardex Feather Finish dries really fast, but better to give it 24 hours to be sure. The final coat when dry should be sanded as smooth as possible before putting on color or sealant.
Is feather finish waterproof?
ARDEX FEATHER FINISH – Laminate Floors and Waterproof Flooring-Carpet-Wood-Tile-Parquet-Soundproofing-Vinyl-Porcelain in Miami Florida Talula Floors.
How thick can you apply ARDEX FEATHER FINISH?
ARDEX FEATHER FINISH can be easily applied with a steel trowel, and used at a true feather edge, or up to 3mm in thickness. For thicknesses of 3mm, and not exceeding 12mm, it is recommended to build up in thin applications or alternatively consult the ARDEX ARDURAPID A 45 datasheet.
How thick can ardex be applied?
ARDEX K 521™ is a pourable, polishable, self-leveling topping for fast-track resurfacing of indoor concrete. ARDEX K 521 can be installed from a minimum thickness of 3/8″ (9 mm) up to a maximum thickness of 2″ (5 cm). Use ARDEX K 521 to provide a polished, “aggregate-exposed” surface.
How do I apply for ardex Township?
For smaller quantities, use 2 parts of powder to 1 part water by volume. Use a margin trowel and mix vigorously for 2 to 3 minutes. Mix thoroughly to obtain a lump-free consistency. The pot life of ARDEX TWP is approximately 15 to 20 minutes at 70°F (21°C).
Is ARDEX FEATHER FINISH flexible?
A flexible sealing compound such as ARDEX ARDISEAL™ Rapid Plus Semi-Rigid Joint Sealant may be installed. b. ARDEX FEATHER FINISH will provide a solid surface to which new flooring can bond, but cannot change the fact that a weak substrate lies below.
Can ardex feather finish be used exterior?
ARDEX K 301™ Exterior Self-Leveling Concrete Topping is a self-leveling topping and underlayment for fast-track resurfacing and smoothing for exterior and interior applications over concrete and approved, properly prepared, non-porous surfaces, including terrazzo, epoxy coatings and ceramic and quarry tile – on, above.
Can ardex be used outside?
ARDEX X 90 OUTDOOR can be installed over substrates with temperatures as low as 40˚F (5˚C) and can withstand driving rains or be grouted in only 2 hours.
Is Henry feather finish the same as ardex?
The Henry Feather Finish is the same stuff as is in this Ardex bag. They are made by the exact same company -just different packaging. I found the Henry at Home Depot. You just have to search because different territories in the US carry different products and brands.
How many square feet does a bag of ARDEX FEATHER FINISH cover?
Coverage: 16.7 sq. ft. per bag at 1/4”, 33.3 sq. ft.Technical & Specification Documents. Brand Ardex SKU 226757.
Can you use ARDEX FEATHER FINISH on walls?
ARDEX PANDOMO® W1 is a self-drying, trowel applied finishing compound for walls and ceilings.
Can you feather finish over tile?
One Million Layers This is where using feather finish concrete over tile counters differs from applying it over a smooth surface. You want to make sure everything is very dry so it adheres well to the counter and doesn’t crack.
How long does ardex feather finish last?
This is very simple and though it’s a bit of a nuisance to have to re-do a project, it really should be something that you can get at least two years out of before re-doing.
Can ardex feather finish be stained?
Do you? I haven’t used this yet, but you can stain with the Ardex SD-M stain and it will adhere. Apparently, other stains will not work.
Can ardex be polished?
ARDEX PC-T hardens fast due to its unique self-drying formulation – it can be polished in as little as 24 hours. ARDEX PC-T is ideal in areas such as retail stores, schools, warehouses, airports and all interiors where a polished concrete surface is desired.
What is the PSI of ARDEX FEATHER FINISH?
Using advanced Portland cement chemistry with a self-drying matrix, ARDEX SD-P is ideal for patching and reaches a compressive strength of 4200 psi. It was developed to reduce curing time on pressed-for-time jobs.
How thick can you pour self level?
QUIKRETE® Fast-Setting Self-Leveling Floor Resurfacer (No. 1249-51) can be installed from 1-1/2 inch (38 mm) thick to a feather edge, although a ¼ inch (6.3 mm) minimum thickness is required for heavy traffic areas.
What does feathering a floor mean?
English translation: applying material to concrete floor to even it before putting in other flooring.
What is floor feathering?
Feather finish irregular floors. Designed to smooth grooves, joins, gaps and grout joint lines over concrete, terrazzo and ceramic tiles. Feather Floor is easily applied to any prepared surface using a steel trowel. Apply sufficient pressure to fill all defects and to feather the product into the subfloor surface.
How do you level a floor?
Pour the liquid-like floor leveler onto the subfloor and smooth it out with a trowel. Gravity will help it settle into the low areas. Remove any excess floor leveler and feather it around the edges so it blends with the rest of the floor. Let the floor leveler dry overnight or as indicated by the manufacturer.
