Table of Contents
Can you router tongue and groove?
Tongue-and-groove joints are commonly made on a table saw. But with the right bits, the joints can be made just as easily on a router table.
Do you cut the tongue or groove first?
Step 1: Generally speaking, it’s easier to cut the groove of a T&G joint first, then mill the tongue to fit the groove. A 1/4-in. straight bit or spiral upcut bit makes an ideal groove-cutter into the edge of a workpiece.
Can you make tongue and groove with a table saw?
To produce a tongue and groove on the table saw, use a dado cutter rather than your everyday blade (unless your stock is 3⁄8″ or less in thickness). I use the two outside cutters to produce a 1⁄4″ cut width when working 3⁄4″ stock. Thicker stock calls for a wider groove.
Does the tongue or groove go against the wall?
Which to Install First. Which side is the tongue, which the groove, and which goes first during installation? The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
Do you nail the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
Do you cut the tongue off the first row of laminate?
Place the first plank with the tongue side towards the wall, being sure to allow 1/8″ for expansion. We recommend cutting off the tongue on this first row to avoid any problem with the expansion gap. If it is too short, cut a new plank in half and use one half to start the second row.
What router bits should I start with?
10 Router Bits Every DIYer Should Own Straight-Cutting Bit. As its name implies, this bit cuts straight, square-bottomed grooves. Rounding-Over Bit. Roman Ogee Bit. Cove Bit. Rabbeting Bit. Flush-Trim Bit.
Do you glue tongue and groove?
The recommended glue for floating installation is Tongue and Groove engineered flooring glue. Glue placement is very important. The glue must be placed along the topside of the groove the full length of the grooved side and end.
How do you do tongue and groove?
Tongue and groove is a method of fitting similar objects together, edge to edge, used mainly with wood, in flooring, parquetry, panelling, and similar constructions. Tongue and groove joints allow two flat pieces to be joined strongly together to make a single flat surface.
How deep should a tongue and groove joint be?
The groove should ALWAYS be slightly deeper than the tongue is long, by as much as 1/16″ for 3-inch wide boards. The reason for this is two-fold. First is to prevent problems during assembly.
Can a router cut a groove in wood?
A router is a power tool used for wood working to cut areas out of a wooden item. This tool can be used for decorating the surface or edge of the wood or cutting “chases” in the sides of the wood to hide pipes and cables. They can be used to shape, cut, groove, and create joins in wood.
What tool cuts slots in wood?
A router is a handy tool to have, being used for cutting grooves (properly called rabbeting), cutting slots in boards, such as for hanging them, trimming the edge of laminate, and cutting various types of tongue and groove joints for putting pieces together.
Can you glue tongue and groove to the wall?
The boards can be glued or nailed to the walls, or both. I recommend a paneling adhesive and toothed trowel, or a paneling adhesive applied from a caulking gun. Follow the adhesive instructions for application.
Can you nail hardwood on the groove side?
To nail the groove, you must nail by hand, but you have a very small space in which to work. In addition, you must countersink every nail to avoid interfering with the tongue of the next plank. For most applications, this isn’t feasible or desirable.
Which side is tongue and which is Groove?
Effectively, in a tongue and groove wood floor, as the name suggests, each plank has a tongue and a groove. On one long side of the plank you’ll find the tongue and on the other long side you’ll find the groove. The same is true on the short sides.
Which direction should I lay my bathroom floor?
As a general rule, make sure to lay your floor in the same direction as the main light source in a room and in the same line as the most frequently used entrance. If there are several doors and windows, then opt for the direction that’s the easiest to install.
How do I make sure my first row of floor is straight?
Snap a chalk line down the middle, measure from that line to within a few inches of the starting wall, and snap a second line parallel to the first. Align your first piece with the second line. Then every couple of rows, measure to make sure you are still parallel with the first chalk line.
Should you glue tongue and groove subfloor?
Many manufacturers recommend applying a continuous ¼-inch-diameter glue bead to framing members and using a serpentine pattern for supports that are 3½ inches or wider. Apply two beads of glue to panel joint locations; a 1/8-inch glue bead applied at the tongue-and-groove joints can further improve floor performance.
Why is my router bit burning the wood?
Chris Marshall: If your router doesn’t haven’t have variable-speed control, it could be spinning the bits too quickly … and fast cutters held against wood equals heat buildup and burning. Try increasing your feed rate. The faster the cutter gets through the wood, the less heat it builds up.
Which way do you hand a router?
When routing by hand, the proper feed direction for inside cutouts (left) is clockwise. Feed the router counterclockwise for routing the outer edges. Inverting a router in a router table changes the feed direction from handheld routing. For inside cutouts, feed the workpiece counterclockwise.
