Table of Contents
What is the depth gauge on a chainsaw chain?
A depth gauge is used to provide a flat surface across the teeth of your chainsaw’s teeth to provide a guideline for filing them down to the same height. Step 1: Place a round file on a tooth on the left hand side and, holding it at a 45 degree angle, pull it in a single direction across the tooth.
Why does my chainsaw chain dull so quickly?
If your chain dulls quickly, then it could be a couple of things. Check your user’s manual to ensure that you are using the right sized file for your chain. Alternatively, you could be applying too much pressure when you file. This will create cutting edges that are too thin and dull quickly.
Which way does a chainsaw chain go?
File the teeth from the inside towards the outside. The easy way to remember the correct direction is that the tip of the file should always point away from the engine. Hold the file at a 90-degree angle to the flat sides of the guide bar. Move the file at a 30-degree angle to the straight line of the chain.
How often do you need to sharpen a chainsaw?
You can mount your sharpener if you use your chainsaw throughout the year as it makes it easy to sharpen the tool and also helps to avoid accidents. In most cases, sharpening the chain should happen after ten times of being in use, while in other situations, you have to sharpen it after every session.
What is the purpose of rakers on chainsaw?
The depth gauge (rakers) on a chainsaw control how deep the cutter teeth penetrate. Because the top plate of the cutter tooth is angled back slightly, it is essential that the depth gauge be lowered as the cutter teeth are filed back.
How much does it cost to file rakers?
Re: sharpening chain, how far down to grind rakers? i use a small flat file that is about 6 inches long, really fine cut. i take 3 strokes per raker for hardwood and maybe one less for soft wood. do them all equal just like when you sharpen the chain. or your chain may start to jump up and down while cutting.
What are the parts of a chainsaw chain?
Four Basic Components of Saw Chain Cutter. Rivet. Drive Link. Tie Strap.
How often should you file rakers?
More experienced cutters have a good feel for how their saw is cutting, and simply take their rakers down whenever they seem to need it. In my case, that’s about once every five sharpenings, more or less, assuming nothing extraordinary happens, like hitting a rock.
When should you throw away a chainsaw chain?
Chainsaw feels unbalanced, cuts unevenly, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesn’t cut correctly- then you need to replace the chain.
Do you flip the bar on a chainsaw?
Chainsaw bars don’t wear evenly. Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Does wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood.
What chainsaw chain cuts the fastest?
The fastest type of chainsaw chain is the square, full-chisel chain made by Oregon. The Oregon Power Cut™ saw chains are low vibration, full chisel cutters. These chains fit bar lengths of 16 inches up to 36 inches.
How do you cut a chainsaw to make it more aggressive?
In general, if you want to have an aggressive cut, you are going to need a chainsaw chain that operates as quickly as possible. A chainsaw chain with full chisel teeth means that you are cutting with a very high speed. Speed being one of the main ingredients behind an aggressive chain, this is clearly vital.
Does skip tooth chain cut faster?
A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. Less drag on the chain means less power is needed to cut through the log. That means the motor on your saw runs faster which keeps it in a more efficient power curve.
Is it worth sharpening a chainsaw chain?
As dozens of cutter teeth chew through dense wood, they’re bound to become dull, reducing the tool’s effectiveness and making it more physically demanding for you to control. Regular sharpening, accomplished by filing, will keep your chainsaw purring like a very rugged kitten.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How long does a chainsaw blade stay sharp?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
