Table of Contents
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do you reset the pilot light on a furnace?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
Should furnace pilot light always on?
Most furnaces with electronic ignition have a device called a hot surface igniter. The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
Why won’t my pilot light light on my furnace?
There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
How do I check my pilot light?
How to Tell If the Pilot Light Is Out Locate the front cover panel on your furnace. It should be a little door that’s easily visible. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color.
How do you reset an automatic pilot light?
Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately.
What causes a pilot light to go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
Should you turn off the pilot light on a gas furnace?
Most modern mid to high efficiency gas furnaces no longer have a pilot light. It’s been replaced by an electronic ignition. As a result, the furnace will not need to continuously burn gas in order to keep a pilot light going, making it unnecessary to turn off your furnace for the summer.
Does leaving the pilot light on use gas?
A pilot light is a small flame that is kept alight using a steady, small stream of gas. This continuous flame is necessary to light large burners such as those found in gas fireplaces.
Where is the reset button on a furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
How do you light a pilot light on a lighter?
With the button depressed, hold the lighter flame near the pilot opening. Continue holding the gas valve to the “Pilot” position for at least one minute after relighting the flame. This allows the thermocouple safety sensor to heat up properly.
Where is the ignitor on my furnace?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
Why is my furnace not blowing hot air?
Heater Not Blowing Warm Air Because of Thermostat Settings. Make sure you check the thermostat which controls your HVAC system. If your thermostat is set correctly and your heater is still not coming on, you may have a faulty thermostat. If these fixes do not work, a call to an HVAC professional is in order.
How much does it cost to relight a pilot?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.
When did furnaces stop using pilot lights?
Why New Furnaces Don’t Have Pilot Lights? Up till about 2010, most furnaces came with pilot lights. After 2010, the trend shifted to electronic ignition systems (intermittent pilots or hot surface pilots).
