Table of Contents
Lighting a Gas Fireplace With a Key Valve Place a long lighter next to the burner and pull the fuel trigger. (You can also use a lit match.) Turn the key in the slot to open the gas valve. You may hear the hiss of gas entering the burner. Replace the key cover. Use the key to control the height of the flames.
Why does my gas fireplace have a key?
Lighting a Fireplace With a Key On some types of fireplaces, a round, decorative slot is used to control the gas valve, and it’s usually located near the fireplace; sometimes, it’s right on the floor. The gas flow is controlled with a fireplace key — sometimes known as the hex key — as the fireplace is lit.
How do you start a fireplace key?
Igniting with a Fireplace Key Look over the user manual included with your fireplace. Remove your fireplace’s outer cover. Put a fireplace key into the device’s gas valve knob. Hold a long lighter up to the burner and ignite it. Turn the gas key. Replace the fireplace’s outer cover immediately.
What is the switch on the side of my fireplace?
What is this? The second handle you may find in your fireplace (usually located on the left inside panel) is a control lever for the outside air kit. When burning your fireplace, the outside air kit lever should always be in the open (or up) position.
What does the switch on the fireplace do?
Gas Fireplace Wall Switch: What, Why & How Simply put, a fireplace wall switch is a toggle switch that opens or closes the circuit between the thermopile and the gas valve. Well, it’s a safety feature that prevents the gas valve from turning on if the pilot light is not working properly.
How do you turn on an old gas fireplace?
The pilot knob has three positions: on, off and pilot. Move the pilot knob to the pilot position. This will allow you to push the knob in, which manually releases the flow of gas to the pilot. Now, while holding the pilot knob in, push the igniter button in once every second until the pilot is lit.
Why is my gas fireplace not lighting?
If gas is coming out of the pilot, but it still won’t light, the spark igniter could be the problem. Alleyne says to look for and clear out any debris between the igniter and thermocouple. The pilot lighting, but not staying lit, indicates that the thermocouple is worn out, Worthen says.
Do all gas fireplaces have a pilot light?
It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”. The best way to determine if you have this type of gas fireplace is to look at the control knob of the fireplace. On a fireplace you will normally find the control knob behind the grate or door.
Can you start a gas fireplace without electricity?
Many gas fireplaces will work without electricity. You can run both intermittent pilot ignition fireplaces and standing pilot light systems during a power outage. IPI valve systems will normally have a backup battery system in place to ignite the flames.
How do I know if my damper is open or closed?
Before lighting a fire, you can tell if the damper is open by placing your hand into the fireplace. If you feel a draft coming down the chimney, it is a good indicator that the damper is open. If you don’t feel any cold air coming down the chimney, it means that the damper is closed.
Do you open the flue all the way?
The damper should always be fully open before lighting a fire and when the fireplace is in use. Close it when it’s not it use. Operating the fireplace with the damper partially closed will not generate more heat. Instead, blocking the passage through the flue will result in smoke entering the home.
How do I control the airflow in my fireplace?
Close the front damper slowly and observe the smoke escaping from the chimney. When the smoke becomes darker or more noticeable, open the damper slightly until it clears again. On modern stoves with two front dampers, make the initial adjustments to the lower damper only to control airflow to the fuel supply.
Where is the gas fireplace switch?
First, locate the fireplace controls, they are located usually behind a louver or panel at the bottom of the fireplace. Next, locate the control knob on the gas valve, it usually has 3 labels Off, On, and Pilot. You will also want to locate the ignitor button; it looks very similar to a starter on a barbecue grill.
What are the 2 switches for on my gas fireplace?
Question: There are two wall switches on the wall beside the gas fireplace. The top switch ignites the flame.
Can you light gas fireplace without pilot?
Natural gas appliances and fireplaces have traditionally used a standing pilot light to ignite the flame/heat source. Because these systems do not rely on external electricity, they work seamlessly even if the power goes out for an extended period of time. This does require electricity to start up.
How do you turn on a pilot light?
Turn the gas regulator valve to the “pilot” position. If the water heater has a manual “ignite” button, press that to light the pilot. If it doesn’t have the button, or the button fails, press the regulator valve and hold a grill lighter or long match to the pilot light valve until the pilot ignites.
Can you use a gas fireplace without logs?
You can use a gas fireplace without logs because the heat source is the burner connected to your gas line. Don’t use wood in your gas fireplace, as they weren’t built for wood to be their fuel source. Instead, use a ceramic log in your fireplace for additional reflective heat.
