Table of Contents
How do I light the pilot on my furnace?
How Can I Restart My Pilot Light? Step 1: Turn off your furnace. Step 2: Locate your gas valve. Step 3: Hold down the red button. Step 4: Light the pilot light. Step 5: Let go of the button. Step 6: Turn your gas back on. Step 7: Turn your furnace back on.
Can I turn on my own pilot light?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
Why won’t my pilot light light on my furnace?
There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
How do you relight your pilot light?
Turn the valve to the “pilot” position. Press and hold the reset button. If the reset button fails, ignite the lighter. Hold down the reset button and bring a grill lighter or long match to the pilot light valve until the pilot ignites.
Should the pilot light always be on in a gas furnace?
Most furnaces with electronic ignition have a device called a hot surface igniter. The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
Why is my furnace not blowing hot air?
Heater Not Blowing Warm Air Because of Thermostat Settings. Make sure you check the thermostat which controls your HVAC system. If your thermostat is set correctly and your heater is still not coming on, you may have a faulty thermostat. If these fixes do not work, a call to an HVAC professional is in order.
Where is the ignitor on my furnace?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
How do you restart a furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
Why is my gas heater not igniting?
One of the most common reasons for your gas heater not igniting or stopped working is because its thermostat is either off or not working properly. Therefore, make sure you check the thermostat, and if it is off, then turn it on while setting it on heat mode (5 degrees above your room temperature, at least).
Why would pilot light go out?
Some of the possible serious reasons for pilot lights to go out include loose or broken gas valves, thermocouples or heat exchangers, faulty venting, low gas pressure, or high winds. If you believe there is a serious problem, don’t hesitate to contact a professional.
How do I know if my pilot light is on?
If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color. Pilot lights should always be blue.
Is it safe to light a furnace pilot?
Once enough time has passed for any lingering gas to dissipate, it is safe to light your furnace pilot light. Turn the switch to “pilot.” As you hold the reset button, bring a flame close to the pilot light opening. Once the light is back on, you can release the reset button.
Should you turn off the pilot light on a gas furnace?
Most modern mid to high efficiency gas furnaces no longer have a pilot light. It’s been replaced by an electronic ignition. As a result, the furnace will not need to continuously burn gas in order to keep a pilot light going, making it unnecessary to turn off your furnace for the summer.
Why is my heat not coming on?
Often, the issue is that the heating system is simply dirty. The system’s heat exchanger cannot work unless there’s sufficient air moving across it to stop it from overheating. In short, a dirty blower can cause the heat exchanger to fail. Dirty air filters could also be the reason your heater stopped working.
How do you reset the pilot light on a furnace?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
What do I do if my furnace is blowing cold air?
How To Troubleshoot Furnace Blowing Cold Air Step 1: Check Thermostat Setting. First and most importantly, make sure your thermostat is set to Heating Mode. Step 2: Evaluate and Adjust Your Vents: Step 3: Assess Furnace Filters and Replace Filters If They Are Dirty. Step 4: Call An HVAC Pro.
How do I turn my furnace on?
Set the thermostat. The thermostat of your furnace should now have power. Select the “Heat” setting on the thermostat, then set the temperature to your preference. When the temperature drops below the thermostat setting, the furnace will turn on and heat your home.
When did furnaces stop using pilot lights?
Why New Furnaces Don’t Have Pilot Lights? Up till about 2010, most furnaces came with pilot lights. After 2010, the trend shifted to electronic ignition systems (intermittent pilots or hot surface pilots).
