Table of Contents
To toggle the pumps on and off, simply press the jets you would like turned off. That will switch off the therapy pump you indicated. Note: The circulation pump cannot be toggled on and off on the touch screen as it is designed to run at all times to keep the hot tub running effectively.
Why wont my hot tub jets turn off?
When jets start failing, the most likely case is that your hot tub pump is not working correctly. Open the access panel and the airlock valve close to the pump. This releases air from the line and purge system, allowing more water to stream through the jets. Clogged filters or water intakes can also cause jet issues.
Should hot tub jets always be on?
A dip in the spa can be a spontaneous event whenever the mood strikes. Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.
Do spa jets turn off automatically?
Why do the jets turn off by themselves? The water jets on almost all systems (Balboa, Gecko, Smart Touch, etc.) will only run for a fixed time, usually 15 or 20 minutes, and then will automatically switch off.
How do you turn the jets on a hot tub?
How to Turn Jets on in the Hot Tub Locate the control panel of the hot tub. This is typically near the hot tub entryway. Turn on the jets. You will see a speed (low, medium, high) that allows you to adjust the force of the hot tub jets. Turn on the timer as well.
Why does my hot tub turn on by itself?
They take into account the temperature, sensing when it falls below a certain level and starting heating. Therefore, when a hot tub is in automatic mode, the timer will start or stop heating when it is necessary, so you don’t have to worry about turning your place on and off according to temperature.
Can I leave hot tub jets on with cover on?
Covering your hot tub with plastic wrap or a tarp is disastrous for your hot tub cover. Not only could it become waterlogged much quicker, but it can also magnify the sun’s rays and trap heat. That can cause your cover’s cores to melt.
What temperature do you keep a hot tub when not in use?
While it may sound like common sense to turn your hot tub down every time it is not in use, it’s actually better to maintain a constant soaking temperature, which is typically around 100° Fahrenheit for many people.
Can you leave water in hot tub off?
Well, in the case of your hot tub, it might not be the best idea. With the hot tub off, it will be unable to circulate and filter the water, that means stationary water which isn’t being circulated. Water sitting in the pipework could end up going stagnant and causing problems when you return.
Can you run hot tub jets without water?
Water left in the pipes and equipment can grow bacteria biofilm, which is difficult to eradicate. Plus, without water, seals and gaskets become dry and begin to leak. Therefore, make sure to not leave your hot tub sitting empty.
Do hot tub jets run when heating?
Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub’s heating. By running the jets, you’re allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.
Why do my hot tub jets keep turning on?
That said, the jets will turn on automatically if the internal temperature falls below what you set it to. For example if it is set to 104, but the internal temp falls to 103, the jets will turn on automatically, until it heats back up to 104 and then turn off automatically.
How do you turn off a jet in a Balboa hot tub?
Each press of “Warm” or “Cool” will adjust the set temperature. After three seconds, the display will stop flashing and begin to display the current spa temperature. Press “Jets” to turn the pump on or off, and to shift between low and high speeds (if equipped). The low speed will turn off after 4 hours.
Do you turn off spa when not in use?
In times of cold weather when you’re not using the hot tub, it’s better to turn the thermostat down rather than turning off the tub altogether. An exception to this is if you’re closing down the hot tub completely. If you’re planning on doing this, ensure it’s done properly to avoid any damage during cold weather.
Should I turn my hot tub off when not in use?
It is necessary to keep it at lower temperatures when it’s not in use so that energy consumption isn’t too high. The reason why you should not switch the hot tub off completely is because it will end up consuming more energy when you’re trying to heat the water up to a certain temperature again.
Where is the power switch on a hot tub?
The pressure switch is often located either on a PVC plumbing part next to the spa pack or directly mounted onto the stainless steel heater manifold or tube. The heater manifold can be found either underneath, inside or attached to the power control box.
