How To Turn Off Air Induction Valve Jet Tub

Table of Contents

While turning off the air induction valve may vary based on your tub manufacturer (always check the manual), general advice is to adjust the jets fully clockwise to turn off air induction. There is usually an “OFF” indicator on the air induction valve that will indicate the direction you need to turn the jets.

How do you turn off the air induction on a jetted tub?

Turn off the air induction valves by turning them fully clockwise. This forces the water to circulate only in the internal plumbing of the tub to concentrate the flow and clean deeper. Leave them open if the manufacturer of your tub states to do so in the owner’s manual.

What is an air induction valve?

(Air Induction Valve) is, to quote the FSM, “The air induction valve sends secondary air to the exhaust manifold, using a vacuum created by exhaust pulsation in the exhaust manifold. When the exhaust pressure is below atmospheric pressure (negative pressure), secondary air is sent to the exhaust manifold.

What are the knobs on my jetted tub?

Water Control Generally, in the form of manual knobs, there are electric versions, but the idea is that the water knobs control the speed and pressure of the jets. Some of these are tied and linked to your electric water pump.

How do you turn off bathtub jets?

If you have massage jets running with therapy pumps and the standard circulation jets you might have a button that says: Jets 1, Jets 2, and Jets 3. To toggle the pumps on and off, simply press the jets you would like turned off. That will switch off the therapy pump you indicated.

Can you use Epsom salt in a jetted tub?

You can use pink Himalayan salts, Epsom salts and Dead Sea salts in whirlpool tubs. These are lovely salts to add to any whirlpool bath and will really help you to feel relaxed. Any of the salts mentioned above are an added bonus and can provide relief for skin problems, anxiety and joint pain.

How do I clean the jets in my hot tub with vinegar?

After filling your tub, simply add 1 cup of vinegar or bleach and 1/2 cup powdered dishwasher detergent. Run the tub jets for 15 minutes. Allow water to remain in tub for one hour, then drain and rinse.

How do you turn off an air induction valve?

How do you clean a hole in an air tub?

However, it’s easy to clean with CLR and a toothpick. If they start to act funky or spray weird or not spray at all, then put some CLR in the bottom with some hot water. Let it sit for about 10 minutes, then drain the tub, then turn the water and jets back on and they should work well again.

What is the difference between a whirlpool and a jetted tub?

The first whirlpool tub was patented by Jacuzzi. The company’s products have since become synonymous with in-home spa tubs and, while Jacuzzi is a brand name, it is often used interchangeably with “whirlpool” or simply any jetted tub. Whirlpool is the generic term for any tub with water jets installed.

What do the buttons on a Jacuzzi do?

Some larger hot tubs may have up to three jet buttons on the control panel that allow you to adjust the speed and strength of your jets. In most cases, pushing the button the first time will turn them on a low setting and pushing it again will increase the speed.

Why won’t my tub jets turn off?

When jets start failing, the most likely case is that your hot tub pump is not working correctly. Open the access panel and the airlock valve close to the pump. This releases air from the line and purge system, allowing more water to stream through the jets. Clogged filters or water intakes can also cause jet issues.

Do bathtub jets turn off automatically?

That said, the jets will turn on automatically if the internal temperature falls below what you set it to. For example if it is set to 104, but the internal temp falls to 103, the jets will turn on automatically, until it heats back up to 104 and then turn off automatically.

Why won’t my Jacuzzi jets turn off?

First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter. If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.

Can I run bleach through my Jacuzzi tub?

When dealing with the bleach, it’s important to run a clean tub of water through, then after ten minutes, drain and rinse the tub thoroughly. Some manufacturers suggest you do not use bleach because it can dry out the internal gaskets of your tub.

How do I know if my jetted tub is air or water?

The main distinguishing feature that sets the two apart is the mechanism by which the jets operate. Simply put, a whirlpool shoots jets of water while an air tub uses jets of air. This can have several implications in regards to upkeep, function and personal preference. The most noticeable difference is the sensation.