Table of Contents
Turn the kingpin nut anti-clockwise to loosen the trucks but do so in small increments and test as you go so as not to loosen the trucks too much. To tighten your trucks, turn the nut clockwise.
How do I keep my skateboard trucks tight?
Use a skate tool or other useful tool to tighten or loosen the big nut in the center of the truck. Turn it clockwise to tighten the trucks, getting tighter turning. Turn it counter-clockwise to loosen the trucks, getting a softer turning feel.
How do I make my trucks tighter?
Lean to turn in a direction (frontside or backside), and gradually press more and more to tighten the turn. You should reach a point where your board resists leaning any further without contacting the wheels. Change directions while you pay attention to how tight you’re able to turn.
How tight should trucks be for beginners?
If you are a beginner, then you should keep the trucks tight as one can easily control the skateboard with tight trucks. On the other hand, loose trucks give a better flow to the skateboard and allow one to do tricks in a better way.
How tight should skateboard truck bolts be?
Make sure that you don’t over tighten your hardware. Tighten them until they are flush with the top of the deck, but don’t counter sink them to where the top of the bolt is below the top of the deck.
Why is my skateboard so wobbly?
Wobbly skateboards are caused by bushings being too soft or the skateboard trucks being too loose. With just a few minor adjustments to the kingpin nut, you can solve this problem. It’s really easy to fix actually and some don’t even consider it a problem. Some people like loose trucks and others prefer them tight.
Why do trucks get loose?
If you skate with tight trucks, loosening them will improve the flow of your skateboarding. Loose trucks also allow for a better landing if the drop wasn’t perfect. You could start with one type and then change the adjustments as your skateboarding develops, finding your own preferences is part of the ride.
What tool do you use to tighten skateboard trucks?
Luckily, loosening and tightening your trucks is very simple, so you can easily make adjustments on the go and continually tweak it. All you need is a skate tool, socket set or spanner to turn the kingpin nut on the underside of your trucks.
What’s the difference between loose and tight?
Tight means fixed or firmly in place, fully stretched or fitting close to the skin. In slang, it means very good or emotionally close. 2. Loose means not fastened or fixed in place and not tight-fitting.
How much should I tighten my trucks?
The nuts should be tightened as far as they can be without impeding the spin of the wheel. Generally you should feel only a very minor amount of play if you try to move the wheel side to side. Occasionally a nut might work itself tighter or looser than originally set and should just be corrected.
Should trucks be loose or tight?
Your trucks should be loose enough that you don’t need to tic-tac to get around obstacles while skating around. Skateboard trucks can be set tight or loose, depending on the rider’s preference. That being said, they should be tight enough that the kingpin won’t fall out and loose enough that the bushings don’t burst.
How wobbly should a skateboard be?
The trucks should be as loose as you feel comfortable when you’re first starting out. Be sure not to compress the bushings when adjusting your trucks. Once you’re comfortable with your board, loosen your trucks up a hair so that they feel slightly uncomfortable.
What happens if your trucks are too small?
What Happens When Your Trucks Are Too Narrow. When you’re trucks don’t match your board and aren’t wide enough you’ll get the carpet riding effect. You won’t be able to see your wheels, just your deck. Just a tad too small doesn’t really matter but at a certain point, you’ll run into trouble.
Can you over tighten trucks?
Over tightening can increase both the chance that the truck will crack and the chance that the screw will pull out.
How can I make my skateboard more stable?
The easiest option to make your TKP more stable (ie, make your skateboard stable), is to simply tighten down the kingpin nut. Doing this makes the bushings deform and bunch up, and it makes your truck feel more stable.
How do I make my skateboard not wobble?
Get low, relax your legs and focus on keeping your upper body over your board and positioned slightly forward. Attack the hill and if your board starts to wobble, stay relaxed and confident. Practice Slowing Down & Stopping!.
Are skateboard wheels supposed to be loose?
Your skateboard wheels should be tight enough that they spin freely. However, you don’t want the wheels so loose that they wiggle on the truck’s axle. It’s also possible to over-tighten skateboard wheels, and that will prevent you from getting the most speed out of your board.
