Table of Contents
Where do you tighten the chain on a chainsaw?
Why won’t my chainsaw chain tighten?
If you can’t tighten the chain, you may not be implementing the proper tightening procedure. To adjust the chain, loosen the nuts that hold the guide bar in place. Attempting to turn the tension screw without loosening the nuts first may be the reason you can’t tighten the chain.
Why is my chain on my chainsaw loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
How much tension should a chainsaw chain have?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why isn’t my chain spinning on my chainsaw?
If your chainsaw blade will not rotate, the chain may be tensioned too tight. If the chain is too tight, the blade may not spin when the throttle is engaged, which can cause damage to the clutch or other associated parts. Keep in mind that the tension of the chain will change with heat.
How do I stop my chainsaw chain from stretching?
Every chainsaw has a tension screw that’s located at or close to the base of the chainsaw bar. If you want to tighten the chain, turn the tension screw clockwise. If you want to loosen up the chain, turn the tension chain counterclockwise.
How do you know if your chainsaw clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Why does my chainsaw stick?
Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
Why is my Stihl chainsaw not spinning?
Common solutions for: Stihl Chainsaw chain not turning Make sure that the stop lever is disengaged. If the stop lever is engaged, the chain won’t turn. If the clutch pads are worn out, replace the clutch assembly. The clutch pads engage the clutch drum to allow the chain to rotate.
How do I stop my timing chain from stretching?
It is important to have your vehicle serviced regularly for oil changes—every 5,000 miles and with the correct oil. Doing so is the best preventive maintenance of timing chain stretch and hop.
What causes chain stretch?
Its elongation is caused when material is removed from the pins and bushings. The individual joints in a roller chain articulate as they enter and leave the sprockets. This articulation results in wear on the pins and bushings. As material is worn away from these surfaces, the chain will gradually elongate.
How often should you replace your chainsaw chain?
When you own a chainsaw and see that it does not cut as well anymore you will have to decide whether to replace it or sharpen the chain. A chainsaw chain could serve you for more than five years if it is occasionally used, and still help you accomplish most of your tasks.
Do chainsaw clutches wear out?
Clutch Replacement When the clutch shoes wear out, it’s usually best to replace the entire clutch assembly because the inside of the drum is probably worn out, too. Start by unscrewing the spark plug and locking the piston with a locking tool or a piece of rope. Then you’ll have access to the clutch shoes.
How do you know if your chainsaw sprocket is worn out?
One of the most important components of the chainsaw is the sprocket. If you feel that the saw is skipping, jerking, or has a drag or stretch, these are signs that your sprocket needs changing.
Do you start a chainsaw with the brake on?
When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Why is my chainsaw chain not sharp?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the chain is too tight, the chain may not rotate at the proper speed, causing the chain not to cut properly.
Why is my chainsaw using so much oil?
An overfilled reservoir can often leak oil when the saw is turned on. Check this and siphon some off if it looks excessively high. If the oil is running out via the delivery line to the bar then there is a chance that the tank vent is plugged up. If so, the chain may be running ‘dry’ during operation.
Why does my chainsaw go blunt quickly?
What is this? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast. It won’t be hard to notice whether the wood that you’re cutting is dirty or not.
