Table of Contents
Why does my chainsaw chain keep loosening?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
What happens if a chainsaw chain is too loose?
A loose chainsaw chain increases the risk of kickback as well as the chances of the saw chain being thrown off the guide bar. Saw chain that is too tight can prevent the chainsaw from turning the saw chain or cause the chainsaw to heat up.
Where is the tension screw on a chainsaw?
Tension adjustment screws are located to the side of chainsaw guide bars. Tightening the screw will tighten the chain, and loosening will loosen the chain. Double check the chain to see that it’s at the correct tightness before moving on.
Why is my chain always loose?
Your chain might simply be too old or can stretch over time. When this occurs you need to replace it. Consider that your loose chain also may be due to operator error. Exceeding the recommended gear range for the rear derailleur on your bike may lead to a droopy chain when you ride in these gears.
How long do chainsaw chains last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why does my chainsaw jump when cutting?
Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain. Place a dime between the chain and bar, then increase the tension until the chain is snug against the dime. Remove the dime and you’re ready to cut.
Why won’t my chainsaw chain tighten?
If you can’t tighten the chain, you may not be implementing the proper tightening procedure. To adjust the chain, loosen the nuts that hold the guide bar in place. Attempting to turn the tension screw without loosening the nuts first may be the reason you can’t tighten the chain.
How do I know if my chain is too loose?
To find out whether your chain is too long take a look at it from the side with your eyes being level with the chain. A loose chain will sag close to or below the chainstays as the chain hangs between the rear cogs and chainring. The chain might skip as you pedal, or even drop off the gears.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
Why does my chainsaw blade go dull so fast?
What is this? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast. It won’t be hard to notice whether the wood that you’re cutting is dirty or not.
Why does my chainsaw blade dull so quickly?
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How do you stop a chain saw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How tight should a chain be?
The chain should be tight enough that it only allows you to move it up and down about half an inch. If there is no slack in the chain then it is too tight. And if there is too much slack then you need to tighten that chain.
Will a loose chain cause loss of power?
A tight chain and a loose chain will both lead to problems. A tight chain will increase friction on the chain and sprockets, leading to greater power loss in the drive train and excessive wear.
Why does my chainsaw bog down at full throttle?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
Why does my chainsaw only runs on choke?
If your chainsaw only runs with the choke on, it is likely an issue with your carburetor. If the carburetor is plugged, the engine will be starved of fuel and will not run. However, if the engine is plugged, the choke will pull more fuel through the carburetor’s idle circuit and allow it to run.
