Table of Contents
Test and Clean Procedure Open the hood of your vehicle. Pull the electrical plug off the control valve. Take out the idle control valve and flip it over. Take your multimeter and set it to “Ohms.” One multimeter lead should touch one end of the valve terminal, and the other lead should do the same for the other end.
How many ohms should a IAC valve have?
Using an ohmmeter, measure the resistance between pins 3 and 2 on the (IAC) valve. Resistance should be 10-14 ohms. If resistance is ok, proceed to the next step.
How do you test an idle air control valve?
To check if an idle control valve is working properly, start by turning on your engine and letting it run for a minute or 2. Then, when it’s at an idling speed, take note of the RPMs in your car.
How do I know if my idle air control valve is bad?
Common signs include irregular or unusually high idle speed, the Check Engine Light coming on, and stalling while idling.Usually a bad or failing idle control valve will produce a few symptoms that can alert the driver of a potential issue. Irregular idle speed. Check Engine Light comes on. Engine stalling.
How do you test a 4 pin IAC valve with a multimeter?
5 Steps on how to test iac valve with multimeter Step 1: Locate the iac valve from service manual. Step 2: Inspect the IAC Valve operation. Step 3: Test the resistance of the coils. Step 4: Check supply voltage from the ECU. Step 5: Check the coil for short circuit and for short circuit to earth.
What happens if you unplug idle air control valve?
If it works properly, stopping it would cause panic to your inactive engine. Normally, if you turn on your car, the inactive air control valve will increase and decrease the rpms engine slowly.
Can a bad idle air control valve cause no start?
4. the car won’t start: in extreme cases, the iac valve may cause too much or too little air from entering the engine when you turn the ignition, resulting in engine that cranks but doesn’t start.
How do I fix code P0505?
What repairs can fix the P0505 code? Replacing the IAC valve and cleaning the throttle body and passages. Removing carbon from throttle body and IAC passages and clean IAC. Repairing a vacuum leak in the engine intake manifold vacuum system or gaskets.
How do you reset your idle air control valve?
Turn the ignition ON and leave on for several seconds then turn the ignition OFF to allow the ECM to reset the IAC valve. You should be good to go.
Can you clean idle air control valve?
How do you clean an IAC valve? After relocating the IAC valve, you need to unscrew it and detach all the wires. You can clean it by soaking it in gasoline and blowing compressed air into it. Then, reattach it with the screws and reconnect the wires.
Can a bad idle air control valve cause white smoke?
White smoke is indicative of antifreeze getting into the combustion chamber, which may be caused by a cracked cylinder head or a bad head gasket. This oil being burnt can be caused by worn piston rings, worn valve guide seals, or even the valve guides itself letting oil seep into the combustion chamber.
What does the code P0505 mean?
Diagnostic trouble code (DTC) P0505 stands for “Idle Control System.” The code may be accompanied by erratic idle speeds that can lead to stalling and other issues. On most older vehicles, the idle control system relies on an idle air control valve (IAC) on or near the throttle body.
How do I clean my idle air control valve without removing it?
How To Clean Idle Air Control Valve Without Removing It Prepare the working area. Locate the idle air control valve. Remove the filter box and the air duct. Disconnect the clamps that connect the air duct to the throttle body. Locate the passage to the idle air control valve. Spray the hole with throttle body cleaner.
What causes rough idle and loss of power?
A rough idling car can be the result of bad spark plugs or a problem with the spark plug wires. The spark plug is technically a heat exchanger to transfer energy within the car’s ignition system. If anything goes wrong with either of those processes, you may notice a rough idle or loss of power.
How long do idle air control valves last?
In general, you will need to replace the IAC valve every three or four years. This will keep carbon from accumulating in the valve and causing you problems. The most common sign that your IAC valve is malfunctioning is that your engine will stall.
What sensors control idle speed?
The computer monitors idle speed by counting ignition pulses from the ignition module in the distributor or crankshaft position sensor when the throttle position sensor or throttle switch signals the computer that the throttle is closed and the engine is at idle.
How do I fix code P0507?
What repairs can fix the P0507 code? Replacing or cleaning the idle air valve. Repairing the intake air leak. Repairing the charging system. Cleaning the throttle body. Replacing the power steering pressure switch.
How do you fix the idle air control system RPM higher than expected?
Check the PCV valve as well and see if it is blocked and needs a new replacement. Inspect the IAC (Idle Air Controller) if it is equipped, and verify its performance. Try swapping in a new throttle body (if available) and see if it can fix the problem.
Why does my RPM go up and down while idle?
If the engine can’t keep idling, it will continue trying to get it revved up to compensate. The cause of the erratic engine you’re experiencing could be a vacuum leak, sensor failure, or an EGR system malfunction.
Can you clean IAC valve with carb cleaner?
Hold the valve pointed downward, and spray the pointed end of the valve with carburetor cleaner, and wipe it clean. (Don’t allow the carburetor cleaner to drip into the housing.) Repeat until all the carbon is removed.
