Table of Contents
Test and Clean Procedure Open the hood of your vehicle. Pull the electrical plug off the control valve. Take out the idle control valve and flip it over. Take your multimeter and set it to “Ohms.” One multimeter lead should touch one end of the valve terminal, and the other lead should do the same for the other end.
How do I know if my idle air control valve is bad?
Common signs include irregular or unusually high idle speed, the Check Engine Light coming on, and stalling while idling.Usually a bad or failing idle control valve will produce a few symptoms that can alert the driver of a potential issue. Irregular idle speed. Check Engine Light comes on. Engine stalling.
What happens if you unplug idle air control valve?
If it works properly, stopping it would cause panic to your inactive engine. Normally, if you turn on your car, the inactive air control valve will increase and decrease the rpms engine slowly.
How do I reset my idle air control valve?
Turn the ignition ON and leave on for several seconds then turn the ignition OFF to allow the ECM to reset the IAC valve. You should be good to go.
How many ohms should a IAC valve have?
Using an ohmmeter, measure the resistance between pins 3 and 2 on the (IAC) valve. Resistance should be 10-14 ohms. If resistance is ok, proceed to the next step.
How do I fix code P0505?
What repairs can fix the P0505 code? Replacing the IAC valve and cleaning the throttle body and passages. Removing carbon from throttle body and IAC passages and clean IAC. Repairing a vacuum leak in the engine intake manifold vacuum system or gaskets.
Can a car run without an idle air control valve?
The engine would be unable to start or run unless the throttle was slightly open, because the IAC’s (Idle Air Control) job is to let a controlled amount of air into the cylinder when the throttle is closed. If the IAC is stuck closed, the only way for air to get in is past the throttle plate.
What causes intermittent rough idle?
The most common cause of rough idle is a vacuum leak or a failed PCV valve. It could also be caused by other air-fuel mixture-related issues like bad fuel injectors, EGR valves, or low compression. In rare cases, it is caused by misfires from a bad spark plug or coil.
How do I clean my idle air control valve without removing it?
How To Clean Idle Air Control Valve Without Removing It Prepare the working area. Locate the idle air control valve. Remove the filter box and the air duct. Disconnect the clamps that connect the air duct to the throttle body. Locate the passage to the idle air control valve. Spray the hole with throttle body cleaner.
How do I reset my idle sensor?
The easiest way to reset your throttle position sensor is to unhook the negative cable from your battery for up to five minutes or to remove the fuse for your engine control module.
How do you test a 4 pin IAC valve with a multimeter?
5 Steps on how to test iac valve with multimeter Step 1: Locate the iac valve from service manual. Step 2: Inspect the IAC Valve operation. Step 3: Test the resistance of the coils. Step 4: Check supply voltage from the ECU. Step 5: Check the coil for short circuit and for short circuit to earth.
Can I drive with a P0505 code?
Trouble code P0505 should be diagnosed and repaired as soon as possible. Not recommended, however, you may drive your vehicle while trouble code P0505 is present unless the engine stall or stumbling is is severe enough to hinder proper vehicle operation. Erratic or lack of idle control may be noticed.
How much does it cost to fix a idle control valve?
The replacement cost of an idle control valve is anywhere from $120 to $500. The cost of the parts alone will be between $70 and $400+, depending on the make and model of your vehicle. The labor cost should only be around $50 to $100 because it doesn’t take that long to remove and replace the old idle control valve.
How do you fix the idle air control system RPM higher than expected?
Check the PCV valve as well and see if it is blocked and needs a new replacement. Inspect the IAC (Idle Air Controller) if it is equipped, and verify its performance. Try swapping in a new throttle body (if available) and see if it can fix the problem.
Can you clean idle air control valve?
How do you clean an IAC valve? After relocating the IAC valve, you need to unscrew it and detach all the wires. You can clean it by soaking it in gasoline and blowing compressed air into it. Then, reattach it with the screws and reconnect the wires.
Will bad IAC cause hard start?
If your vehicle has the 4-liter V-6, the problem may be a faulty idle air control valve. Whenever you start the engine, the throttle is closed so the valve meters the proper amount of air for combustion. If it allows too much or too little, the result is hard starting and often rough idle.
Can you drive with a bad IAC?
Technically, you may be able to drive with a bad IAC—but you should not continue doing so. A bad IAC can potentially lead to stalling, which can compromise vehicle safety. Plus, you won’t pass a state emissions test if the check engine light is on due to a bad IAC.
