Table of Contents
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
How do you test an electronic ballast with a multimeter?
To measure it, set your digital multimeter to around a thousand ohms resistance setting. Connect the black leads to the white ground wire on your ballast. Afterward, test every other wire with the red lead. When you do this test, a good ballast will return an “open-loop” or max resistance.
How do you tell if a ballast is going out?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
How long do fluorescent ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
What does a bad ballast smell like?
A common source of these odors is the fluorescent light ballast. When called to such an incident, you typically will find an electrical odor or a haze of smoke. Overheating ballasts often exhibit symptoms. They may cause the bulb to flicker, shine, dim, or not work at all.
How do you check the voltage on a ballast?
Test the ballast’s voltage with a multimeter. Attach the multimeter’s leads to the sockets at the ends of the ballast. If the reading is not between five and nine volts, replace the ballast. Adjust the multimeter to measure frequency and replace the ballast if the reading is not between 20 and 50 kilohertz.
What is the output voltage of a fluorescent ballast?
Fluorescent lamps use a ballast which transforms line voltage to a voltage to start up and operate the lamp(s). Newer fluorescent ballasts are usually rated for both 120 volts and 277 volts. Some are rated for only 120 volts, others for only 277 volts (used in commercial environments).
How do you check the voltage on a fluorescent light fixture?
Turn the setting on the multimeter to “Ohms.” Touch one probe to the white wire and the other to a colored wire. The meter will display a direct short or continuity. If no reading is displayed, there is a problem with the ballast. Replace it as soon as possible.
Why my tube light is not working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
Why do my fluorescent lights keep burning out?
There are many possible reasons why a light bulb burns out quickly: The power supply voltage may be too high. Bulbs may be loose or connected improperly. Excessive vibrations may be causing the filament to break.
Can you repair a ballast?
While simply swapping burned out bulbs in an existing ballast is deemed “ballast repair” by many – and can offer advantages in longevity and energy savings – sometimes this simple “fix” is not enough.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How much does it cost to replace a ballast in a fluorescent light?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Can a bad ballast cause a fire?
As with any electrical situation where overheating is possible, a bad ballast can pose a fire danger. The overheated ballast could cause the plastic housing on the light itself to melt and, in the right conditions, flame up.
