Table of Contents
What Are Signs Your Blower Motor Needs to Be Replaced? Poor or Airflow from Air Vents. This will be the first and most obvious sign your blower motor has a problem. No Airflow At All From Vents. Skyrocketing Energy Bills. Strange Noises When You Turn on the Heat. Overheating Blower / Weird Smells.
How do I know if my blower motor resistor is bad or blower motor?
If there is no air coming out of the vents… If there is no air pressure blowing from the vents, then your blower motor resistor needs to be replaced in order to start working again. Usually, overheating is the cause to a failed blower motor resistor.
What can cause a blower motor to stop working?
In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.
Is there a way to test a blower motor resistor?
Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.
What happens if blower motor relay goes bad?
If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.
Where is the blower motor reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do I reset my blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
How much does a new blower motor cost?
Replacing a blower motor costs $450 on average with a typical range of $250 to $800. With a warranty, you might pay as little as $150 for labor alone. For high-end models, like those with large motors or access issues, you might pay as much as $2,000.
How do you test a blower motor switch?
Test the switch. Plug the connector back in to the blower motor, and then trace the wire harness back to the connector closest to the blower motor switch, usually located under the dash. Disconnect the connector and set the multimeter to ohms.
Why is my furnace not blowing hot air?
Heater Not Blowing Warm Air Because of Thermostat Settings. Make sure you check the thermostat which controls your HVAC system. If your thermostat is set correctly and your heater is still not coming on, you may have a faulty thermostat. If these fixes do not work, a call to an HVAC professional is in order.
Can you drive a car without a blower motor?
Your car’s blower motor is not only necessary for the operation of your air conditioner. Without a functioning blower motor your engine runs the risk of overheating. Start car and see if blower motor works. If fuse blows again, check for loose circuits.
Why does my blower motor resistor keeps melting?
Trent, one of the biggest reasons for blower motor resistors to have shorten life is actually because of faulty blower motor drawing too many amps, some times melting wires/plugs, heating up resistors shortening their life. Many Dodge forums tell of this problem.
How do you test a blower motor with a multimeter?
Using a multimeter set on the Ohm scale, use the positive lead and test the black wire. To check the purple wire for current, use your ignition key and turn it to the run setting, turn the heater power to full power and set the multimeter to DC power. If your meter reads “no current” the motor is no good.
What does a bad blower motor sound like?
A defective blower motor will make a continuous sound noticeable by the passengers in the vehicle. It can manifest as a knocking, whirring, clunking, vibrating, squealing, or whining noise that persists until the blower motor is replaced.
How do I test my furnace blower motor?
How To Check your Furnace Blower Motor (7 Steps) Step 1: Turn off all power to the furnace. Step 2: Remove the Furnace Access Panels. Step 3: Use your voltage tester to ensure no electricity is flowing through the furnace. Step 4: Feel the area near the blower motor to determine if it’s hot.
Why is my air conditioner on but not blowing air?
If the AC unit is running, but there is no air through the vents, you are likely dealing with a fan capacitor that has reached the end of its life. Fan capacitors help get your HVAC system’s outdoor and indoor fan motors blowing and your compressor running.
How do you manually reset a furnace?
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
Is there a fuse for the blower motor?
Many vehicles have two fuses for the blower motor, one in the interior fuse block and the other under the hood. The blower motor is usually under the dashboard on the passenger side.
Why is my furnace not starting?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
