Table of Contents
Look for dark areas at the base of the bulb. When bulbs age and have been used for a long time, brown spots will appear. If darkness begins to form at the ends of the tube, the bulb may be near its end. While they may still light, they are wearing out and will die soon.
How do you tell if a fluorescent bulb or ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
Why do fluorescent lights not turn on sometimes?
If you find your fluorescent light won’t turn on sometimes, there could be a variety of reasons why. It could be as simple as needing to replace the bulb or plug the light itself in; or, it could be something more serious, such as a blown fuse or a damaged/dying starter.
How can you tell if the ballast is bad?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
Why my tube light is not working?
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
Will a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
What happens when a ballast fails?
But there is a good chance your ballast could be the cause of your lighting woes if your lights are dim, buzzing, changing colors, or flickering rapidly. You should check all parts of the fixture, including the bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit.
What does a bad ballast smell like?
A common source of these odors is the fluorescent light ballast. When called to such an incident, you typically will find an electrical odor or a haze of smoke. Overheating ballasts often exhibit symptoms. They may cause the bulb to flicker, shine, dim, or not work at all.
How long does a fluorescent tube last?
LED tubes last an average of 50,000 hours (roughly 16 years) while fluorescent T8 tubes last an average of 25,000 (roughly 8 years).
How long should a fluorescent light ballast last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
When should fluorescent bulbs be replaced?
Fluorescent bulbs can go for years without replacement—even when the ends start to blacken. Don’t worry about them until the light they put out starts to weaken.
Why are my fluorescent lights flickering?
If your fluorescent bulbs flicker, most likely the problem is with the bulb itself. If the bulb is very dark on either end, it may be defective and burned out. The best way to test the functionality of a bulb is to put it into a fixture you know works. Flickering fluorescent lights can also be a result of temperature.
Why does my fluorescent light take so long to turn on?
Most fluorescent light fixtures also have a component called a ballast, which controls the current through the fixture. If the ballast is malfunctioning, it too can cause the light to take a while to turn on. But ballasts are very expensive to replace and they malfunction far more seldom than tubes and starters.
Why is the tube light blinking?
Lamp blinks: This is usually because of a poor connection where the tube fits into its sockets at each end. Take the tube out and clean the pins at each end with fine steel wool. Brush dust out of sockets, then reseat firmly.
How do I know if my fluorescent light has a starter?
You can easily tell if your fluorescent fixture has a starter as it will have a small silver (or white) cylinder directly behind the tube.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Why are my new fluorescent bulbs not working?
If a fluorescent tube neither lights nor flickers when switched on, first check to see that the fixture is plugged in and that no fuse has blown or circuit breaker has tripped. If this does not help, try wiggling the tube gently in its sockets by rocking it back and forth and from side to side.
How much does it cost to replace a ballast in a fluorescent light?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
How do I know if my ballast is T8 or T12?
If no markings are available, the size in diameter of the tube is the easiest way to determine the type you have installed. T8 tubes are 1-inch in diameter and T12 tubes are 1 1/2 -inch.
