Table of Contents
Gather Tools and Materials. Turn Off the Water Supply and Open the Faucet. Remove the Handle Cap, Handle and Faceplate. Remove the Locking Clip. Remove and Replace the Cartridge. Replace Other Parts and Test. Remove the Metal Stem in a Shower Faucet with Two Handles. Replace the Metal Stem if Needed.
Why is my shower faucet dripping?
When water drips or drizzles from a shower head, there is a problem with the shower faucet (valve). In most cases, inner seals are worn, or parts have become corroded or clogged with hard water deposits. And the rubber O-rings and gaskets that seal connections between moving metal parts wear down with time and use.
Why does my shower faucet drip after I turn it off?
Once you turn off the water, gravity pulls the diverter back into the “faucet” position, and any water remaining in the pipe up to and in the shower head simply falls back down and out the faucet. Over time, the diverter can get gummed up with soap scum or hard water deposits, making it hard to move freely on its own.
How do I get my bathtub faucet to stop dripping?
How it’s done Shut off the water supply. The first step when fixing a leaky bathtub faucet is shutting off the water supply. Remove the cap from the faucet. Unscrew the handle screw. Remove the handle. Remove the escutcheon. Remove the stem assembly. Check the washer. Replace the washer.
Where is the O-ring in a shower head?
The O-ring, a circular rubber part of the fixture, is inside the showerhead. It attaches to the various threads when the head has been unscrewed. When this part of the showerhead breaks, it can cause leaks and may need to be replaced.
Where is the water shut off valve for a shower?
This supply valve is usually near the bottom left side of the toilet tank. For showers/tubs, look around the tub or shower for an access panel. It may be on the other side of the wall from the tub or shower.
How do I stop my hand held shower head from leaking?
How to Fix a Leaky Hand-held Showerhead Step 1: Remove the Flexible Hose. Step 2: Clean and Check the Threads. Step 3: Inspect the Rubber Gasket. Step 4: Soak Off Mineral Deposits. Step 5: Tape the Threads. Step 6: Reconnect the Flexible Hose. Step 7: Install New Rubber Washers. Step 8: Install a New Rubber Gasket.
How do I change the O-rings in my shower faucet?
Step 1 Shower Handle O-ring. Use your groove joint pliers to loosen and remove the escutcheon plate. Using your groove joint pliers, loosen and remove the cartridge stem. Slowly unscrew and remove the stem completely. Using your flat head screwdriver, remove the screw from the end of the stem cartridge.
How do I change the O-ring on my shower?
Replacing the O-ring is simple. Just pull the valve stem out and remove the old O-ring. Put a small amount of petroleum jelly or silicone on the new O-ring and slide it on the stem. Before you reattach the escutcheon, you can apply a little bathtub caulk.
Can I turn off the water to just my shower?
There usually is not a shutoff valve for just the shower. The toilet has it’s own shutoff, and sinks have their own shutoffs under the sink. But tub and showers typically do not have their own shutoffs. You’ll usually see a copper line come off the hot water heater and run off towards the kitchen and baths.
How do I fix a leaky shower?
Gather Tools and Materials. Turn Off the Water Supply and Open the Faucet. Remove the Handle Cap, Handle and Faceplate. Remove the Locking Clip. Remove and Replace the Cartridge. Replace Other Parts and Test. Remove the Metal Stem in a Shower Faucet with Two Handles. Replace the Metal Stem if Needed.
What is a shower O-ring?
The O-ring is a small rubber part located in the inside of a faucet spout, to prevent leaks. If your faucet won’t stop dripping from the spout, the cause is most likely an old, worn out and damaged O-ring.
Can a shower valve leak?
A shower valve leak within the wall can cause significant damage to your home and lead to tile replacement. When ignored, even a small leak can have adverse effects within the wall cavity. It can be imperative that you act fast to minimize the damage a leaking shower valve can cause.
Why does my shower head leak when I turn on the water?
More often than not, a dripping showerhead is the result of worn or damaged inner seals. Over time, these wear down, and when they do, water starts to leak out. The leak can also be caused by worn or damaged washers or O-rings in the shower’s valve.
What is valve for shower?
A shower valve is found behind the handle of a shower faucet. It controls the temperature of the water and turns the shower on and off. Through a temperature mixing valve, the hot and cold lines are mixed together to create the desired temperature. Kingston shower valves are also pressure balanced.
Do you need to turn off water to change shower faucet?
Turn off the water supply. Unless you happen to have a separate cutoff valve installed in the bathroom, shut off the water to the whole house. Open up a faucet at a lower level in your home to relieve pressure in the lines and leave it open as you work.
