Table of Contents
What is a Stihl 025 worth?
Stihl 025 Price And Parts It’s all going to depend on the condition of the saw and the market, but a good example will sell for $200 – $250. An 025 in good condition for under $150 is a steal. On eBay at the time of writing, they are priced between $31 and $300, so you can see there is a lot of variation.
Why won’t my Stihl saw start?
If you can’t start the engine, the fuel may be contaminated if the saw has been in storage, and you should change it. If starting is still difficult, use a toothbrush to clean the spark arrestor – located behind the muffler – and change the spark plug and fuel filter, which is located in the gas tank.
How do I start my chainsaw for the first time?
How to Start a Chainsaw Step 1: Stabilize the Chainsaw. Step 2: Engage the Chain Brake. Step 3: Turn the Chainsaw On and Open Up the Choke. Step 4: Prime the Fuel. Step 5: Pull the Starting Cord a Few Times. Step 6: Close the Choke. Step 7: Let the Chainsaw Idle. Step 8: Close the Choke.
How do you start a chainsaw that won’t start?
To solve this problem, open the spark plug hole with it facing away from you to drain all the fuel in the tank. Deactivate the choke by pushing in the control then pull the starter cord 6-8 times as you press in the throttle control. Dry off the spark plug and refit it back in place.
What causes a chainsaw not to start?
The chainsaw’s engine is flooded with fuel. A fuel issue is one of the most common reasons why a chainsaw won’t start. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again.
What spark plug does a Stihl 025 take?
Spark Plug For Stihl 023 025 026 024 MS230 MS250 MS240 MS260 MS361 Husqvarna 51 55 61 268 272 272XP 340 345 346XP 350 Chainsaw, NGK BMP7A L7TC Spark Plug For Many Stihl Husqvarna Echo and other Machines OEM# 1110 400 7005. Parts Name: Spark Plug.
What size chain is on a Stihl 025?
The Stihl 025 and newer model MS250 (and the 023/MS230) will take two chain sizes and types: 1) the 3/8″ PICCO – . 050″ on 12, 14, 16 and 18 inch bars, and 2) the . 325″ – . 063″ on 15 and 18 inch bars.
Are Stihl chainsaws hard to start?
Regular maintenance will help to ensure that your Stihl chain saw will always start. In addition, some storage steps can help with starting when the chainsaw has been left for an extended period. Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.
How do I reset my Stihl carburetor?
Return a type A carburetor to its factory setting by turning the “H” screw counterclockwise until it stops, turning the “L” screw clockwise until it is seated, then backing it off one full turn.
Why does my chainsaw dies when I give it gas?
Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.
How do you adjust a Stihl carburetor?
Turn the H screw clockwise with a carburetor adjustment tool until the head is spinning as fast as it will go, then back off the screw carefully until the RPMs start to decrease. Turn the screw slowly clockwise again until the engine once again just starts to pick up speed.
Why does my Stihl chainsaw stall?
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
Why does my Stihl chainsaw bog down?
The Job of the Carburetor Without the right amount of air and fuel in the piston cylinder, the 2-cycle engine in a Stihl chain saw runs inefficiently and the saw loses power. When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.
How do you start a chainsaw after sitting?
So how can you fix it? Just let the saw sit for 30 min and the excess gas will evaporate. Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again. Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.
How do you start a Stihl chainsaw without flooding?
Pull the starting rope five or six times to clear fuel out of the combustion chamber. Replace the air filter and spark plug, and connect the spark plug wire. Leave the choke open and pull the starting cord several times. The chain saw should start.
How long to wait if chainsaw is flooded?
Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions.
What spark plug does a Stihl chainsaw take?
For the best performance from your STIHL tool, we recommend that you always use the STIHL NGK spark plug.
What is the spark plug gap on a Stihl chainsaw?
What is the correct spark plug gap for my STIHL trimmer, chainsaw, or blower? The correct gap setting is 0.020″.
What CC is a Stihl 021?
STIHL 021 35.2cc Petrol Chainsaw.
