Table of Contents
Instructions Prepare Work Area for Sanding. Choose a ventilated, protected area, such as outside under a patio cover, in a garage with the door open, or in a well-ventilated shop. Remove Obstructions. Sand Furniture. Remove Dust. Prepare Area for Staining. Mix Stain. Begin Staining. Wipe Excess Stain.
What stain should I use on furniture?
Oil-based stains are the best wood stain for furniture or any large wood surface because of the slower drying time, which gives the piece a more even finish. Oil-based stains tend to penetrate deeper, leaving behind a richer color that is easy to refresh by applying another coat.
Do I need to seal wood after staining?
After staining wood do you have to seal it? After staining wood, you have to seal if because the wood remains a porous surface. If you’re just using a regular stain, it can provide some degree of protection compared to totally unfinished wood.
How many coats of stain do you need on furniture?
2 coats. To deepen the color, apply a third coat. Optional, for additional luster or sheen a clear protective finish can be applied. Recommended finishes include Minwax® Fast-Drying Polyurethane or Minwax® Wipe-On Poly.
Is it better to stain with a brush or rag?
Brushing is the slowest method of applying stain. So not only might you get blotching or lap marks, you’re also wasting time. It’s more efficient to wipe stain than to brush it, and you’re less likely to have color problems.
How long should stain sit before wiping?
Wipe the stain off immediately if you’d like a lighter tone. But for a deeper tone, leave the stain on the wood for 5 to 10 minutes before wiping it off. Be sure to wipe off all the excess stain going in the direction of the grain of the wood.
Should I use a rag or brush to stain wood?
Using a lint free rag is the best way to apply wood stain because it is great for controlling the amount of stain that is applied and for removing any excess stain. Also, the rag leaves a beautiful, even, and brush stroke free finish. It also can easily be thrown out once finished.
Should I use oil or water based stain?
If the wood is going to be in direct exposure to wind, rain, and sunlight, an oil-based stain is the best choice. This is because it is more durable than a water-base and will provide a more complete protective layer against these elements.
Is it better to paint or stain wood furniture?
Furniture pieces with mild to moderate flaws that you can sand out are great to stain—the right stain can cover the imperfections and make the item look new again. For furniture with severe flaws that you cannot easily fix by sanding, paint will better cover these issues and make the piece look new again.
Should you wet wood before staining?
Wet the wood with water before applying the stain to raise the grain and leave a rougher surface for more pigment to lodge. This adds an extra step because you have to let the wood dry for this trick to work. Don’t try to sand the stain smooth or you will most likely sand through in places.
Can you stain wood without sanding?
If the wood has been stained but not finished, DO NOT scuff or sand. Doing so will remove the color from the edges, leaving the project looking uneven.
Do you need to sand wood before staining it?
It all starts with sanding. You need a smooth surface with no blemishes because stain will highlight scratches and dings in the wood. Always sand down to clean wood (if you have enough meat left of the wood) before applying any stain. Too rough and the wood will be very dark almost to the point of being black.
What happens if you don’t seal wood stain?
Wood is dried-out and dull if you do not apply some sort of sealer. Staining and finishing are two very different things. By applying pigments, a stain is meant to darken or dye wood, but the wood is not preserved by staining.
Should you polyurethane over stain?
Do I have to apply a clear coat after staining? While staining creates a rich, deep color that highlights natural wood grain, it does not provide long-term protection. A polyurethane top coat protects the wood from scratches, stains and water damage.
Should I sand after staining?
Sand thoroughly before you apply the first coat of stain. Sand a few times, with progressively finer grit sandpaper. Keep in mind that you will probably have to do a few coats of stain to provide the level of protection you want for your project. It’s important to wipe away excess stain as you apply each coat.
Can you leave stain on without wiping?
Stain can be left on without wiping off. However, the heavier the application of stain, the longer it takes to fully dry before a topcoat can be applied. Typical stain dry time before recoating is 1-2 hours. Leaving stain on without wiping off creates the richest, darkest shade of the stain on the wood.
Which lasts longer paint or stain?
While staining may take less time than painting, painting often does a better job of filling the cracks, covering imperfections, and provides longer lasting protection. Paint also is typically more rot resistance and does a better job of preventing mold and sun damage.
What kind of cloth should I use for staining?
Cheesecloth: White 100% cotton cheesecloth is great for staining. Since it is a thinner material, it is easier to fill the wood grain and covers your surface better. To use, simply bunch up and start wiping stain on your surface.
Can you wipe stain off with paper towel?
To keep this from happening you must wipe off excess stain after applying it. But my go-to method for applying stain is to use a rag. Old t-shirts are great for this, but even paper towels work for smaller projects. But again, I can’t stress enough how important it is to wipe it down with a clean dry cloth.
Is a foam brush good for stain?
Foam brushes are fine for applying Minwax® Pre-Stain Wood Conditioner and any Minwax® stains, but they don’t lay down a smooth final topcoat finish like quality bristle brushes do. Also, be sure to use a damp cloth as a final cleanup on the wood before staining or topcoating.
How do you dispose of rags for staining?
Gather your stain-soaked rags and take them away from the house or workshop where you were using them. Lay the rags over metal hangers or the edge of a metal trash can. Allow the rags to cure, or dry, until they are stiff and dry. Place the rags, once completely stiff and dry, into a garbage bag.
