Table of Contents
Stain the Deck Boards Don’t stain yourself into a corner. Stain the deck boards using a paint pad applicator. Apply one coat of stain in long, even strokes. Use a paintbrush to stain between cracks and in any problem areas. Once you’re finished, clean the brushes and paint tray.
Is it better to brush or roll stain on a deck?
The agitation and friction caused by a paint brush will cause the wood to absorb more stain. So if you are spraying or rolling the stain, always back-brush it in with a brush while the stain is still wet; you’ll achieve much better penetration in to the wood.
What’s the best way to put stain on a deck?
Apply the deck stain with a natural bristle brush. A roller gets the job done faster, but brushing helps force the stain into open grain and pores. It’s especially important to work stain into butt joints where two boards meet.
Do I need to strip my deck before staining?
Strip and Renew Wood Before Restaining Solid-color stains protect wood decks and look great when new, but even the best solid color deck stain eventually flakes and wears away. At that point, they need to be scraped and stripped off before the deck can be recoated.
What to use to clean deck before staining?
Deck cleaners, such as the Wood Deck Cleaner and Brightener by DeckWise or the TimberTech Deck Cleaner, will lift and remove any stuck-on grime from your wood deck boards. These deck cleaning solutions will soak down into the dry wood.
How many coats of stain should you put on a deck?
The general rule of thumb is to apply only as much deck stain as the wood can absorb. Typically this will be 2 coats, unless your dealing with extremely dense hardwoods which may only be able to absorb 1 coat of wood stain.
What if it rains after I stain my deck?
If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.
Can you use a roller to stain a deck?
A paint roller can be used to roll stain on. A wide 18-inch roller may work well for staining a few fence or deck boards at a time but a mop or stain pad will hold more stain lessening the amount of time you have to dip back into the stain bucket.
What temperature should it be to stain a deck?
Helpful Stain Application Tips Apply stain only at the proper temperature. For most stains, 70 degrees Fahrenheit is the optimum, with the safety range from 50 to 90 degrees Fahrenheit.
When should I stain my deck for the first time?
You can stain a new deck immediately after installing your deck, but this is not the best time to do it and here’s why: the lumber is still too wet. The best time to stain a new deck is 3 to 12 months after installing it.
Will pressure washing remove deck stain?
Pressure washing is a quick way to remove a deck finish, but it requires some care so as not to damage the deck. A pressure setting of 1500 psi should be strong enough to clean away deck stain. Hold the sprayer about 3 inches off the surface and move the sprayer as you work in the same direction as the grain.
Can I stain over stain without sanding?
You do not need to sand off the previous stain and finish. The purpose of the light sanding is to give a little tooth to the surface to help your new stain colour stick.
Why is my decking stain peeling?
Deck stains will generally peel for two basic reasons: over application and poor adhesion. This is simple — too much stain on the surface of the wood. With deck stains, specifically with semi-transparent finishes, more is not better. You only want to apply as much product as the wood can easily absorb.
What happens if you don’t clean deck before staining?
Before you apply stain, make sure the surface is clean (no dust, dirt, wood fibers or grease), dry and free from mildew. When a surface is not clean, stains and other finishes have trouble sticking and may end up peeling.
Can I use OxiClean on my wood deck?
OxiClean is safe to use on decks. When cleaning your outdoor deck, the oxygen bleach is a much better alternative than chlorine bleach as it cleans any deck surface without causing discoloration or damage to plants, shrubs, soil and similar surroundings.
Do you need to apply a sealer after staining a deck?
Most of the time, stains also contain a protective sealant. It’s a good idea, though, to re-seal your deck (or check that it needs to be re-sealed) once a year. Water-based stains can adhere to water or oil-based coatings already present on the wooden surface.
How do I know if my deck needs a second coat of stain?
A good rule of thumb is to lightly touch the portion that has been stained. If it feels tacky to the touch (a little sticky and not wet) then you can apply the second coat.
How long should deck dry before staining?
In perfect drying conditions, 48 hours is enough for the wood to get to where it needs to be before staining. Decks that don’t get much sun should be given an extra day to dry out. If after a day or two the wood still looks wet or there are soft spots, give it more time to dry out.
Do I have to wait 4 hours between coats of stain?
For a deeper color and sheen, wait one hour and apply a second coat. After 1 hour, the surface is dry to the touch. Wait overnight before subjecting the wood to normal use. For a deeper color and sheen, wait one hour and apply a second coat.
