Table of Contents
Can I sharpen my own lawn mower blade?
The fastest way to sharpen a lawnmower blade is with a bench grinder. Wearing protective eyewear, earplugs, and work gloves, grind the edge of the blade against the spinning wheel. It’ll be loud and you’ll see sparks, but you’ll be able to sharpen the blade in a matter of a few minutes.
How do you sharpen a lawnmower blade by hand?
Sharpen a Lawn Mower Blade by Hand: Put on protective eye gear and gloves. Sharpen the edge of the blade using a 10-inch file or grindstone, keeping the file at roughly a 45-degree angle. Sharpen from the top side of the cutting edge. Push the file in one direction along the blade.
How do you sharpen a lawn mower blade without removing it?
How to sharpen lawn mower blades without removing them? Collect the required tools. Seal the gas tank. Tilt the mower and place the wooden block under it on the other side to give it support. Clean the blade with water and a steel brush. Use the angle grinder or flat-file to sharpen the cutting edge slowly. Lower the mower.
Do you sharpen both sides of a mower blade?
Always sharpen from the top side of the cutting edge; this will give you the longest-lasting edge on the blade. Note: The file cuts in one direction only, on the push stroke; you’ll feel it bite into the steel on the blade.
How sharp does a mower blade need to be?
In general, you will want your lawnmower blade sharpened to about a 30-degree angle. The blades should be sharp enough to cut the grass without tearing or ripping it, but not so fine that the edge is razor-thin and easily damaged by the terrain or small debris in your lawn.
What is the best angle to sharpen a lawn mower blade?
Lawn mower blades come from the factory with a specific angle on the angled edge. This angle should be kept as you grind your blades over time. The most common lawn mower blade angle is 30-35 degrees. When sharpening your mower blades it is important to keep this 30-35 degree angle over time.
How much does it cost to sharpen lawn mower blades?
Depending on the type of your mower, you can expect to pay anywhere between 20 dollars to 60 dollars. If it’s a reel lawn mower you might not even need to take the blades off the mower and sharpen them while they’re attached.
What tools do I need to sharpen a lawn mower blade?
There are few different ways to sharpen lawnmower blades, including using a bench grinder, hand file, rotary tool, or angle grinder. But here’s a quicker, easier and more accurate method: use a drill and sharpening stone that’s specifically designed for putting a cutting edge back onto dull lawnmower blades.
How often should mower blades be sharpened?
Typically, most home owners just need to sharpen blades twice per season. One good sharpening at the beginning of the season and one around the middle of the mowing season should be good. If you mow over debris such as sticks or rocks, however, you may need to sharpen your blades more than that.
Should you sharpen mulching blades?
Mulching blades are supposed to be sharp so they can cut through grass, leaves, and other debris. Sharpen the mulching blades with a file until they easily cut through the grass, then tighten the blades onto the lawnmower’s deck. The blades should be sharpened twice per season.
How do you tell the top and bottom of a mulching blade?
Look at both sides of the mulching blade. Most blades have the word “bottom” stamped on them, or they have a model number imprinted onto the underside. Whether a word or a number, that side of the mulching blade must face the ground after it is installed and the mower is standing upright.
Can a mower blade be too sharp?
Mower blades should be aggressively sharp, but not as sharp as a razor’s edge. You should be able to touch the blade with your hand without getting cut. Contrary to popular belief, a lawn mower blade with a razor sharp edge will not cut grass better.
Should you sharpen new mower blades?
As mentioned above, brand new lawn mower blades do not need to be sharpened because they are always sharpened during manufacturing. At the very least, your mower blades will benefit from being sharpened once at the beginning of each year.
Does wet grass dull mower blades?
Cutting wet grass can dull the blade more quickly. Clean blades thoroughly before and after mowing a lawn when wet to keep the cut as sharp as possible. Maintain your machine and sharpen mower blades regularly to deliver a clean, healthy cut.
What happens if you cut grass with a dull blade?
Grass cut with a dull mower blade. Dull lawn blades can lead to lawn discoloration, lawn disease, portions of grass being pulled up during mowing, ragged-looking grass, or even the plant dying. Grass that is cleanly cut can recover more easily, which reduces the risk of disease.
Should lawn mower blades feel sharp?
Mower blades should be sharp, but they do not need to be as sharp as a razor blade. When you touch the blade, you should not cut your hand. That way, they will cut the grass seamlessly and have a clean but. Very sharp blades will get dull quickly and need to be sharpened much more often, shortening the blade life.
