Table of Contents
Does pool pump go before or after filter?
The pool pump connects to the pool filter’s intake valve and pumps water through the filter. The filter transfers the filtered water into the chlorinator, which then releases the water back into the main body of the pool.
How do you hook up an above ground pool pump?
How close should pump be to above ground pool?
If circumstances allow, stay close to the pool. Shorter pipe runs = less work for the pump which extends the life of the pump and uses less electricity. Our projects typically average a distance of 20–40 feet from the pool to the equipment, but as stated earlier, much longer runs are sometimes required.
What should my pool pump be set on?
The “Filter” setting circulates water through the sand or DE media, then out the filter through the return port to the pool. This is the standard setting for normal pump and filter operation. The “Backwash” setting redirects the flow of water backwards through the filter media to flush out contaminants.
How do you start a pool for the first time?
Step 1 – Clear off the water, debris and anything else from the pool cover. Step 2 – Remove the pool cover. Step 3 – Pull the winter plugs and accessories out. Step 4 – Top up the water in your pool. Step 5 – Reinstall the pool ladder. Step 6 – Prepare the pool filtration system. Step 7 – Power your filtration system up.
How do you prime a pool pump that is higher than the pool?
Steps to Prime Your Pool Pump Turn off the pump. Switch to recirculate. Release air. Clean out the pump basket. Fill the pump basket. Once the pump basket is filled and tightened, make sure the air release valve is open and turn the power to the pump on. Check the water flow to your pump.
How do you install an above ground pool filter?
Measure the area needed for the pump and filter to sit on. Within a couple feet of the skimmer in the pool, measure out the area for the pump and filter. Connect the skimmer. Connect the return hose. Connect the filter discharge. Fill your filter with sand or place the cartridge in it.
How much space does a pool pump need?
Although there is no way to determine exactly how much room you need without knowing the size of your pool, Midwest Fiberglass Pool Distributors notes that the average pool owner should set aside a patch of ground approximately 4 feet square for a built-in pool’s pump and filter system.
How far should pool heater be from pool?
Install the heater as close to the filter as possible and approximately 25 feet away from the swimming pool. Installing the unit any farther may cause heat loss since tubing is underground. An “ideal” installation will have about 24″ of clearance around the unit with no obstructions above.
Which way should pool returns face?
To give your swimming pool the best filtration you should point your return jet away from your skimmer and downward to get the best circulation and filtration. The top few inches of your pool is usually the dirtiest and for your pump to clean properly it is best to keep the water calm on the top of the water.
Should all valves be open on pool?
From left to right, they are SPA MAIN DRAIN, CLEANER, SKIMMER, and POOL MAIN DRAIN. For the cleaner to operate at maximum efficiency, only the skimmer and cleaner valves should be open. No other valves should be open. So it is either main drain+skimmer or cleaner+skimmer.
What is waste setting on pool filter?
WASTE/DRAIN: Another filter bypass setting, but this setting sends the water out of the waste pipe (hose), instead of returning it to the pool. This setting is used to lower pool water level or to vacuum to waste, which is best when vacuuming algae or heavy amounts of dusty, silty debris.
At what speed should I run my pool pump?
Run the circulation system one (1) hour for every 10°F of air temperature if a single-speed filter pump is installed. Example: If it is 100°F, the pump should run 10 hours a day minimum. Of course, if the pool is full of algae or a major weather event has occurred, the pump may need to run 24-hours a day.
How many rpms should I run my pool pump?
Suction cleaners typically run at around 2200-2400 RPM. Heaters require 20 to 40 Gallons Per Minute (GPM) so might run at around half speed or a little higher. You would probably want to run your Spa at up to full speed, 3450, for maximum effect.
Do I need to shock my pool when I first fill it?
At first you’ll add chlorine in what’s called “shock” levels – an extra heavy dose to start your pool off. A shock dose coupled with extra circulation will ensure that all the water gets treated properly in the beginning. Now it’s time to keep the water hardness in check, otherwise known as alkalinity.
What chemicals do you put in a pool for the first time?
Chemicals Needed for Pool Start Ups Stain & Scale Preventer. Granular Shock Chlorine. Chlorine Tablets. pH Increaser and/or pH Decreaser. Alkalinity and/or Calcium Increaser. Cyanuric Acid (Stabilizer) Algaecide and Clarifiers if needed. Complete Test Kit or Test Strips.
How soon after filling a pool Can you swim?
Wait about 20 minutes after adding balancing chemicals to your newly filled pool, and you should be good to swim. Calcium chloride – If you have hard water issues, it’s advised to wait about 2-4 hours before swimming after adding calcium chloride to soften your pool’s water—or until one filter cycle has been completed.
