Table of Contents
How to Start a Hot Tub in 12 Easy Steps Rinse and Drain. If you’re a new hot tub owner, you’re going to have to get used to the cleaning that comes with hot tub ownership. Turn off All Power. Clean the Empty Hot Tub. Install or Clean the Filter. Fill Your Hot Tub. Prime the Pump. Add the Start-Up Chemicals. Run the Pump.
What chemicals do I put in my hot tub for the first time?
This all-in-one kit includes all the essential items you will need to start up your hot tub, including: AquaChek 6in1 Test Strips (50 Strips) Granular pH Minus (2 lbs.) Granular pH Plus (1.5 lbs.) Granular Non-Chlorine Shock (2 lbs.) Liquid Prevent II (16 oz.) Granular Chlor-Aid (2 lbs.).
How should I prepare for a hot tub?
Featured Power Down. You’ll be emptying your spa of water and performing additional maintenance on it, so shut off the heater and turn off the spa. Empty the Spa. Drain your hot tub of all water. Clean Filters. Loosen Fittings. Blow Jets. Clean the Shell. Cover Your Tub.
When should I add chemicals to my hot tub?
To dose your hot tub ready for bather use, we advise using chlorine or bromine granules rather than tablets, which should be added only when your Hot Tubs pump is running. It is important to ensure your spa water is at a normal level of 3-5 parts per million (ppm) for free chlorine and 4-6 PPM for bromine before use.
When can I add chemicals to my hot tub after filling?
Add initial chemicals according to the “Refilling Your Spa” section of the Operation and Care Guide. 12. 24 to 48 hours after the spa has been operational, check alkalinity and pH with test strips or test kit—adjust accordingly. Do not complete this step until this water is hot and has been in for 24 or more hours.
What is best to put under a hot tub?
Gravel is a suitable base option for a hot tub. However, you shouldn’t use inflatable hot tubs directly onto loose gravel, as the surface wouldn’t be flat enough or even. Plus, you’ll need an additional layer of protection as a ground cloth to place underneath the hot tub to keep the surface flat.
Should you shower before hot tub?
It is most important to shower before you use your hot tub to remove sweat, dead skin cells and personal care products such as cologne and deodorant. This reduces the work required from your hot tub filter and water care system to keep your hot tub water clean and balanced.
What is the best base for a hot tub?
A concrete surface is an excellent base for your hot tub as this material is extremely sturdy and long-lasting. If you have an existing patio made of concrete bricks, make sure it’s in good condition and is level (not angled for drainage). A customized poured concrete pad is an even better choice.
How do you get a hot tub in your backyard?
In most cases getting the hot tub into the backyard is fairly simple and straightforward. A delivery crew will bring the hot tub to your home and then place the hot tub on its side on a hot tub cart. Then they roll the cart into your backyard and to the spot you would like the hot tub placed..
How difficult is it to move a hot tub?
It’s not a difficult process, but draining the water from your spa before moving it isn’t simply a matter of emptying the shell; you’ll also have to drain the pumps and pipes. We recommend that you recycle your hot tub water; in most cases, it’s easy to do.
How much does it cost to keep a hot tub running?
In general a small hot tub will cost around $7-$10 a week to keep heated and a large spa $10-$15 a week. Extra large spas will cost more but with a heat pump this can actually be less. In summer if you choose to run the spa bath cold the running costs will be just $2-$3 a week.
What temperature do you add chemicals to a hot tub?
Once the temperature of your hot tub reaches about 80 degrees Fahrenheit (30 degrees Celsius), you can start adding chemicals. Warm water will allow the granular chemicals to dissolve properly.
Should I shock my hot tub after refilling?
It is a good practice to shock with dichlor when you refill your spa. After that, regular maintenance can normally be accomplished with non-chlorine shock. Other times for shock treatment include before or after heavy use and when the spa has been neglected.
How do I add chemicals to my hot tub?
Mix dry granular or powdered chemicals into a bucket of spa water to dilute them, and then add the contents of the bucket to the spa. Avoid splashing chemicals by adding the chemicals to the water rather than water to the chemicals. Do not mix the chemicals with each other before adding them to the hot tub.
How do you balance a hot tub after filling?
For water with high Alkalinity (over 150 ppm), use the pH Minus chemical or other acid to lower the level, which will also lower your pH somewhat. After filling the spa, adjust alkalinity to the 80-120 ppm range. Spa pH should be in the 7.2 – 7.6 range.
What happens if you put too much chlorine in a hot tub?
If theres too much chlorine it will vaporise and form gas that floats just above the surface of the water. If this vapor is inhaled it can inflame airways and exacerbate certain breathing conditions. Read more What Temperature Should My Spa Pool be at and Why?Jul 13, 2020.
How much chlorine do I put in a 300 gallon hot tub?
For a 300 gallon spa, 0.7 oz of Chlorine Granules shaken over the water surface, will raise the chlorine level up to about 10 ppm. This should be done with a balanced pH (in the low range of 7.2-7.4), and with the circulation pump running on high to help distribute the shock quickly.
