Table of Contents
How-To: Choose Cabinet Hardware Types of Cabinet Hardware. Knobs have smaller profiles than handles, are less expensive, and can be used for both drawers and cabinets. Pulls are larger than knobs, make more of a statement, and tend to be easier to grip. Select a Style. Choose a Finish. Don’t Be Afraid to Mix Metals.
How do I know what size hardware for cabinets?
There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.
What should I look for when buying cabinet hardware?
Factors to Consider When Buying Cabinet Handles 1.The Comfort levels of the handles. Cabinet handle design and style. The cost of cabinet handles. Material and Finish. Cabinet handles manufacturer. 1.Polished Brass. Chrome finishing. Polished Nickel finishing.
Can you mix knobs and pulls on kitchen cabinets?
Yes. You can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.
What size should cabinet pulls be?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
How do you measure for cabinet pulls?
To accurately measure existing fixing centers, open your kitchen door or drawer and measure the distance between the center of each screw. This measurement should be used when specifying your new handles.6 days ago.
Should cabinet pulls be vertical or horizontal?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
How do you decide on pulls or knobs?
Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.
What hardware looks good on white cabinets?
Hardware on white cabinets will stand out and steal the show, so it’s a great opportunity to go bold! If you have warm tones, go with gold, black, or bronze hardware. If you have a cold grey tone, then silver, pewter, black, and stainless steel hardware will work.
Where do knobs go on Shaker style cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
How long should bar pulls?
Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.
Is zinc a good metal for cabinet pulls?
Zinc is a good metal for cupboard pulls. Zinc alloy is a safe material for manufacturing cabinet hardware. Furniture handles, which are produced using zinc alloy material, are very durable and long-lasting. It is a material that is resistant to bad weather, moisture, and water due to its zinc composition.
Are cabinet pulls or knobs better?
In many instances, knobs make it easier to open upper cabinets. Pulls, on the other hand, offer easier operation of lower cabinets. Just take a look at this Victorian kitchen. You’ll notice that all the upper cabinets have knobs, while the majority of the lower cabinets feature pulls.
Should my kitchen cabinet pulls match my faucet?
Most of the time the kitchen faucet should match cabinet hardware!” But, sometimes strategically placing different metals next to each other can work for you, add interest or even make a statement.
Should drawers have knobs or pulls?
One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull. It is much more comfortable to open a drawer using a pull.
What is the rule of thumb for cabinet hardware?
An oversized cabinet door or drawer needs a large piece of hardware for proper functionality. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob.
Can you mix cabinet pull sizes?
There’s no “rule”, it’s a matter of looking at as many kitchens as possible and figuring out the look you prefer. I also used a variety of sized pulls on drawers of different widths, and used Restoration Hardware.
What size cabinet pulls for 36 inch drawers?
Oversize Drawers (36″ or larger) For larger drawers, consider investing in longer-length stainless steel pulls such as 6”, 8”, 10” or even 12”. Another alternative to this is by using double smaller pulls, such as two 3” or two 5” pulls.
Where should Pulls be placed on cabinets?
Pulls. Pulls are another versatile option that can be installed on both cabinets and drawers. For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door.
How do you measure a hardware drawer?
The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.
