QA

Question: How To Sand Hard To Reach Places

How do you sand an irregular surface?

For sanding irregular edges of table tops, chair legs, etc., use a deck of cards as the sanding block. The cards and sandpaper will adjust to the contour of the surface you are sanding. This makes a sanding block that is quite flexible, yet provides a firm base for holding the sandpaper against a curved surface.

Which sander is used to sand in corners and tight places?

But then I discovered the detail sander, which is designed to make short work of sanding corners, edges and other tight spaces. Detail sanders feature a small vibrating triangular “head” to which you attach sandpaper.

How do you sand concave surfaces?

Sanding Concave Surfaces With DIY Foam Pad/Random Orbital Step 1: Cut Polystyrene Into a Circle the Same Shape As Your Pad. Cut Polystyrene into a circle the same shape as your pad. Step 2: Spray Adhere One Circular Sheet of Hook&loop to Foam. Step 3: Attach Sanding Disk to the Other Side.

Should I sand with the grain?

No matter what type of edge you’re going for, always maintain steady pressure and sand with, not against, the grain. Don’t employ sandpaper to remove things like pencil marks or dried glue, but do use it to smooth joints or filled nail holes.

How does a delta sander work?

Orbital Sanders The triangular version for sanding into very confined spaces is called a Delta sander. The orbital action is driven by the motor which rotates the pad in a tiny circular motion at high speed.

What is a mouse sander used for?

What is a mouse sander best used for? The peculiarly shaped pad in this sander helps it to reach inside crevices, small corners, and other tight spaces. For this reason, the sander is used frequently to sand odd shapes, seams, corners, and most of the extremely small and tight spots.

Should you wet wood before sanding?

After sanding the wood to about 150- or 180-grit, wet it with a sponge or cloth just short of puddling. Let the wood dry. Overnight is best, but three or four hours is usually sufficient if the air is warm and dry. Then sand the raised grain smooth with the same grit sandpaper you used last or one-numbered grit finer.

Can you sand wood too much?

If wood gets over-sanded in one spot, it starts to become uneven, with a distorted sort of appearance. This can happen to even the most experienced woodworker. Usually this starts simply by attempting to sand out a discoloration, defect, scratch or gouge.

When should you stop sanding?

Typically you will want to stop at 180 or 220 if you are planning to stain the wood. Higher grits will close the pores of the wood and make it difficult for stain to penetrate.

How can I sand fast?

How to Sand Wood Faster Grab a second sander. Double your productivity. Sand faster with suction. Keep the surface clean. Stop the swirls. Slow and steady wins the race. Save your sanity. Music makes the job easier. Stack ’em and sand ’em. How to use a sander: Sand across the grain. Premium paper works faster. Prevent glue spots.

How fine should you sand wood before staining?

On most raw woods, start sanding in the direction of the grain using a #120-150 grit paper before staining and work up to #220 grit paper. Soft woods such as pine and alder: start with #120 and finish with no finer than #220 (for water base stains) and 180 grit for oil base stains.

What can I use if I don’t have a sander?

Sand and a piece of leather or cloth, Pumice (a porous vulcanic Rock), Walnut Shells, Rottenstone (similar to Pumice), Wood Shavings, Corn Cobs, a Wood File, Scraping, Burnishing, or even building a primitive sanding tool are good alternatives to sandpaper.

What is the roughest sandpaper?

What Is Sandpaper Grit? Sandpaper grit is sized by a gauge number, with lower numbers signifying larger, coarser grits. For example, #24- or #40-grit sandpaper is a very coarse, rough sandpaper, while the #1,000-grit paper is extremely fine with very small abrasive particles.

What happens if you sand wood against the grain?

Stephen Rosasco: Sanding against the grain leaves noticeable scratches in the surface; they can usually be sanded out afterward. John Swanson: You may not ruin it, but the surface will have more tear-out. This can be overcome by sanding with the grain on your final, finest grit.

How do you sand a tight corner?

Cut or fashion a 1/4-by-3/4-by-3-inch piece of wood into a long, sharp wedge. Fold the sandpaper over the sharp end and use it to sand inside tight corners. The wedge works similar to a surgical tool, allowing you to sand in short, focused strokes with some power behind them. Cut the wedge smaller if needed.

How much wood can you sand down?

3 Answers. It is not feasible to sand down a wooden member by a whole half of an inch. If something is too long then cut off the additional half inch using a saw. If something is too thick (wide) by the half inch then rip saw off that extra thickness or use a planer to remove it.

What will happen if you put too much pressure on a sander?

When you use too much pressure, the sander has to do more work to perform its rotations, this means there will be more work for the motor and more friction on the surface of the workpiece. More heat can either cause the sander to shut off or potentially lead to pre-mature loading of your sheets or discs.

What is the difference between 80 grit and 600 grit paper?

For heavy sanding and stripping, you need coarse sandpaper measuring 40- to 60-grit; for smoothing surfaces and removing small imperfections, choose 80- to 120-grit sandpaper. For finishing surfaces smoothly, use a super fine sandpaper with 360- to 600-grit.