Table of Contents
What should you not do with a chainsaw?
Don’t Cut on the Ground When Using a Chainsaw Cutting on or near the ground puts you at risk for sinking the bar into the dirt. When learning how to use a chainsaw safely, one of the first things you should do is make sure to make your cuts off the ground.
How do you use a chainsaw for beginners?
If you’re starting the saw between your legs, place the back handle between your thighs and hold the front handle firmly with your left hand. Pull the starter handle with your right hand until the engine fires. Push the choke and pull until the saw starts. Release the chain brake.
How do you stop a chainsaw kickback?
Ways you can avoid chainsaw kickback Read the manual. Make sure the chain brake works before you start. Use low-kickback chains. Use a sharp chain. Be wary when felling tree trunks. Pay attention to the nose of your chainsaw bar.
How dangerous are chainsaws?
There are many high risk and highly likely hazards associated with chainsaw use. Some common hazards are: you can cut yourself, kick-back, noise, vibrations, eyes injuries, the chain can derail/break, head injuries, back injuries, crushing under falling tree and so on.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Should you wear gloves with chainsaw?
Always wear protective gloves when using a chainsaw. Chainsaw gloves are just one component of what you should wear when cutting wood. The other essentials are: Chainsaw chaps, protective head gear and a cut-resistant jacket.
What is chainsaw kickback?
Kickback is the term to describe the unexpected upward motion of the guide bar. Kickback occurs when the end portion of the nose of the bar (the kickback zone) strikes an object and the chain momentarily snags, or is pinched.
Is it hard to operate a chainsaw?
Chainsaws are relatively easy to use once you get used to them but they are dangerous. They will cut flesh and bone as if it is not there.
Can you cut wet wood with a chainsaw?
Yes, you can use a chainsaw to cut wet wood.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
What happens if you hit a nail with a chainsaw?
If chainsaw teeth occasionally come in contact with a nail hidden inside the wood, it can cut through the nail but not without consequences. Every time your chainsaw accidentally cuts a nail, this metal-on-metal contact will cause the chainsaw’s teeth to become dull prematurely.
How do you treat a chainsaw wound?
How to Treat Your Cut at Home Apply direct pressure to the wound. If possible, elevate the wound above the heart. Do not tie a tourniquet around an affected limb. If bleeding stops, let some water run over the wound. If muscle, tendon, bone, or organs are exposed, do not try to push them back into place.
Are electric chainsaws dangerous?
Because electric chainsaws are easier to operate than gas chainsaws, you may think that they’re a safer tool to use; however, that’s not necessarily the case. In some ways, an electric chainsaw may actually be more dangerous to a person who’s using a chainsaw for the first time.
How do chainsaw accidents happen?
CHAINSAW ACCIDENTS Kickback is the most serious risk of chainsaw operation. It occurs when the tip of the guide bar and chain contact an object, forcing the guide bar violently backward and upward. Kickbacks can occur in less than one-tenth of a second, causing severe head, face, neck, shoulder, and hand injuries.
How long should chainsaw blade last?
The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
How many people are killed by chainsaws every year?
They can also quickly cause severe injury or death. According to the Centers for Disease Control and Prevention (CDC), approximately 36,000 people are injured by chainsaws annually.
Why do you need chainsaw chaps?
The main purpose of safety chaps is to protect and guard the legs when using the chainsaw or cutting a tree. In situations where you accidentally drop your power saw, the layers embedded within your chap can conveniently offer maximum protection to your limbs. Also, chaps will protect you from flying splinters.
What is a Kevlar glove?
Kevlar gloves are a type of personal protective equipment (PPE) made of Kevlar, a strong synthetic fiber used to protect workers from cuts, abrasions and heat. The gloves are also lightweight, flexible and comfortable.
What is the best type of gloves to use when operating a chainsaw?
Chainsaw Glove Materials We found goatskin gloves to be the most comfortable products on the market. Kevlar fibers offer excellent cut and puncture protection. PVC palms will let your grip your tools and provide ample dexterity. Neoprene cuffs are form-fitting and provide a snug fit during use.
