Table of Contents
Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. Alternatively, the UniFi AP may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.
How do I factory Reset a UniFi AP?
Physical Reset Press and hold the reset button for 10 seconds while AP is connected. Release the button (the LEDs on the UAP will stop glowing). Do not disconnect the UAP from its power source during the reboot process. The UAP will restore factory settings.
How do I force adopt UniFi AP?
Adoption via the UniFi Network web application Launch the Network web application from unifi.ui.com. Open the UniFi Devices page. Select the device that is ready for adoption. Click Adopt.
How do I Reset my UniFi Network?
Resetting an Unifi Switch Power off the device. Just unplug the power cable. Forget the device in the controller. Unplug all network cables. Plug power back in. Wait until the led turns dark blue. Press the reset button for 5 seconds. Adopt the device in the controller.
How do I factory Reset my Ubiquiti AP lite?
Follow the steps as outlined below: Press and hold the reset button for 10 seconds. Release the button (the LEDs on the UAP will stop glowing) Do not disconnect the UAP from its POE injector during the reboot process. The UAP will restore factory settings.
How reset UniFi AP AC LR?
Restore to Factory Default Settings Press and hold the Reset button for more than five seconds. Alternatively, the UniFi AP may be reset remotely via a Reset button located on the bottom of the Gigabit PoE adapter.
How reset UniFi AP AC Pro?
How to Reboot Unifi Access Point from Unifi Controller Log in to the Unifi Controller. Click on the Devices Tab. Click on the Access Point you wish to restart. On the right-hand side fly in click on the tools icon. Scroll down and click on Open Terminal. On the terminal that opens type in reboot and hit enter.
How do I remove UniFi AP from controller?
Removing an Old Device from the Network Connect to the UniFi Controller and go to Devices. Click on the Device you wish to remove, the Properties window will open on the righthand side. Click Config near the top of the Properties window. Click the plus (+) symbol to expand the Manage Device section.
How do I adopt a UniFi AP via SSH?
Download, install, and run: Ubiquiti Device Discovery Tool. Click “Scan” Click “UniFi Family” to switch to the UniFi device view. Copy the IP address of the device. Download, install, and run: PuTTY. Enter the IP address of the UniFi device, Port 22, Connection type: SSH, and click “Open” Log in.
How do I connect to UniFi AP?
Step 1a: connect the access point Take the power cable and network cable for the access point. Plug 1 end of the network cable into the access point. Plug the other end into the (modem) router. Plug power cable into a free socket. Plug the other end of the power cable into the access point.
What is the default IP for UniFi AP?
1. X scheme if you are connecting to the AP using its default IP of 192.168. 1.20.
How do I reset my ubiquiti router?
Power-on reset Disconnect the Power Cord from the Power Adapter. Press and hold the Reset button while connecting the Power Cord to the Power Adapter. The port LEDs will light up in sequential order. Keep holding the Reset button until the LED on the last port starts flashing, and then release the button.
How do I reset my UniFi cloud key?
Press and hold the reset button and then power on the Cloud Key by connecting it to the power source. Keep the reset button pressed for about 10 seconds, or until you see the recovery LED pattern in a loop (blue – off – white).
How do you reset an app?
How to reset an app to its initial state on Android devices In Android Settings, tap on Apps or Apps & notifications. Tap on Apps again. The list of apps installed on your Android device. Tap Storage. Tap Clear Data. Confirm the removal of the app’s data and settings. On Chrome’s Storage page, tap Manage Space.
How do I reset my UniFi WIFI?
Remove the LAN cable or PoE injector to stop the power supply to the access point and then re-connect the cable. This process will reboot the access point. Unplug and re-plug the Ethernet cable and it will reboot the access point. Each access point can be rebooted in the same way.
How do I reboot my access point remotely?
Restart access points remotely using the CLI Sign in to the command line console (CLI) as the admin user. Type 5 for Device Management. Type 3 for Advanced Shell. Type awetool and press Enter. Using the arrow keys select option 1 Connect to an AP and press Enter.
Can you use UniFi AP without controller?
UniFi APs can run by themselves without the controller unless features like guest portal is enabled (as UniFi controller also functions as a captive portal). Restarting the controller won’t restart your APs.
What is the default password for UniFi AP?
As long as the UniFi Access Point has not been previously setup or adopted by the software, and only if you are attempting to connect via SSH, then always use the default username and password of ubnt / ubnt.
How do I change my UniFi AP IP address?
How to Change the IP Address for your Ubiquiti Access Point Find the IP Address of Your Access Point. If you didn’t know, Ubiquiti Access Points have a default IP address of 192.168. Login to the Web Interface. Change the IP Address on Your Access Point.
How do I manually add UniFi AP to controller?
Manually Adding Ubiquiti Unifi Access Point To Unifi Contoller Write down (or take a picture on your phone) the MAC address for the new AP. Connect the new Unifi AP. Check DHCP to see what IP address was given to the Unifi AP by searching for the MAC address in the DHCP clients table.
