Table of Contents
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system. The water heater’s gas valve is located near the bottom of the unit and connects to your home’s natural gas line.
Why is my Rheem water heater not heating?
Check the power supply to the water heater. Check to see if a fuse has blown or a circuit breaker is tripped. Replace the fuse or reset the breaker. Ensure that the disconnect switch, if used, is in the on position.
Where is the reset button on a gas hot water heater?
A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.
What causes reset button on hot water heater?
If your water heater reset button keeps tripping, one of your heating elements may be broken or worn out. As this component is used to heat water, your hot water heater won’t work without it. When the reset button on a water heater thermostat keeps tripping, the metal casing of the heating element may have cracks.
When should I reset my hot water heater?
Your water heater reset button is a safety device that shuts off power to your water heater when the water temperature inside it exceeds 180 degrees Fahrenheit. Side note: the reset button is also sometimes referred to as the ECO (emergency cut off) switch or “high limit safety thermostat switch”.
Why is my water heater not getting hot?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Other simple solutions include an unplugged or faulty power cord for electric water heaters. For gas water heaters, it could be as straightforward as being out of gas.
Does a water heater have a reset button on it?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. If your water heater now has power, you’re all set.
Where is the pilot light on Rheem water heater?
Push down the red button to the left of the gas knob. Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. You can see the pilot light through the viewing window on the water-heater’s inner door.
How do I know if my Rheem water heater has a pilot light?
You can see the pilot light through the viewing window on the Rheem water heater’s inner door. Continue to hold down the red button for one minute after the pilot light is lit and then release it. The pilot light will remain lit.
How long does it take for water heater to heat up after reset?
Once you’ve reset the system, you have to wait for hot water (unless you have an on-demand water heater), but for how long? It depends on the size of the tank, but with any unit, you should be able to get in a hot shower with gas water heaters within 30-40 minutes and with electric tanks, about 60-90 minutes.
How do you reset the ECO on a Rheem electric water heater?
To reset it, you’ll need to press the red reset button on the ECO, which is usually attached to the upper thermostat. When a water heater starts tripping the ECO repeatedly, it’s time to call a plumber for service.
How do I reset my thermostat?
Reset the Thermostat The method to reset your thermostat will vary depending on the model. Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
Why is my hot water not working but my cold water is?
If hot water pressure suddenly stops entirely but cold water flow continues just fine, then a control valve may have been left closed, or a valve may have failed internally (appearing to be turned on but actually “off” internally due to a broken valve stem part), or a valve or pipe elbow may have become partly blocked.
Why is my hot water only warm?
Sediment Is Affecting the Heating Element The resulting sediment can reduce the lower heating element’s effectiveness, causing only lukewarm to flow from your hot water tap. To fix this problem, make sure your hot water tank is flushed annually to remove any minerals.
What is the most common problem with water heaters?
Water leaks are perhaps the most common type of water heater issue you’ll face. Any water heater will start to leak eventually, as by nature water will eventually corrode your tank and create microscopic cracks or fractures. However, this isn’t always a sign that your tank is what’s leaking.
Can I relight my hot water heater?
If your heater’s pilot goes out, you can relight it yourself. Turn the gas regulator valve’s knob to “Pilot,” press down on it and hold it down. This starts the flow of gas to the pilot burner. On some water heater models, you press and hold down a separate red button to start the pilot burner gas flow.
