Table of Contents
Head to the electric panel and locate the water heater circuit. If it has flipped off, flip it on. Remove the panel cover and locate the reset button behind the insulation. Press it inwards until it clicks in place and then releases.
How do I reset my Rheem water heater?
Turn the water heater’s gas valve switch to the “OFF” position, wait for a few seconds and then flip the switch to the “ON” position to reset the system.
How do I reset my electric hot water heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
Why is my Rheem water heater not heating?
Check the power supply to the water heater. Check to see if a fuse has blown or a circuit breaker is tripped. Replace the fuse or reset the breaker. Ensure that the disconnect switch, if used, is in the on position.
How do I reset the ECO on my electric Rheem water heater?
To reset it, you’ll need to press the red reset button on the ECO, which is usually attached to the upper thermostat. When a water heater starts tripping the ECO repeatedly, it’s time to call a plumber for service.
Why is my electric hot water heater not working?
If an electric water heater is not producing hot water, it could be a simple problem like a blown fuse or tripped circuit breaker. Other simple solutions include an unplugged or faulty power cord for electric water heaters. For gas water heaters, it could be as straightforward as being out of gas.
Is there a reset button on an electric water heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
What causes reset button on hot water heater?
If your water heater reset button keeps tripping, one of your heating elements may be broken or worn out. As this component is used to heat water, your hot water heater won’t work without it. When the reset button on a water heater thermostat keeps tripping, the metal casing of the heating element may have cracks.
When should I reset my hot water heater?
Your water heater reset button is a safety device that shuts off power to your water heater when the water temperature inside it exceeds 180 degrees Fahrenheit. Side note: the reset button is also sometimes referred to as the ECO (emergency cut off) switch or “high limit safety thermostat switch”.
How do I set the temperature on my Rheem water heater?
Pull the insulation from the cavity behind the covers to expose the thermostats. Insert a small flat-head screwdriver into the slot on the thermostat dial. Rotate the thermostat to your desired temperature. Make sure to adjust both thermostats if your Rheem water heater has two access covers.
How do you turn on a electric water heater?
Electric water heaters don’t have a pilot, so the process is simple. First, make sure the breaker that controls the water heater is switched off. Check for any open valves or faucets and close them. Then, turn on the cold water to let the hot water tank fill.
Where is the pilot light on Rheem water heater?
Push down the red button to the left of the gas knob. Hold the red button down while pressing the piezo ignitor striker, found to the immediate right of the gas knob, repeatedly until the pilot is lit. You can see the pilot light through the viewing window on the water-heater’s inner door.
How do you reset the pilot light on a water heater?
Turn the knob to “Off,” and then wait five minutes for the gas to clear before you follow these steps: Open the door/cover over the pilot light access. Use a flashlight or a headlamp to find the burner inside. Turn the gas knob to “Pilot,” press and hold it down. While still holding the gas down, light that pilot.
Where is the fuse on an electric water heater?
The heater is usually fused in the main electrical panel but some electric water heaters may be fed from a separate fuse or circuit breaker box. If the fuse is blown or breaker is tripped, replace the fuse or re-set the circuit breaker.
How do you test a thermostat on a electric water heater?
Test the lower portion of the thermostat, by touching one lead to the common terminal (next to the temperature setting) and the second lead to the left heating element terminal. If the water in the tank is below the thermostat’s set temperature, the multimeter should read close to zero ohms of resistance.
How long does it take for water heater to heat up after reset?
about 30 to 40 minutes Water Heater Type Time to Heat Back Up Gas Tankless 0 mins Electric – Conventional Tank 60-80 mins Electric Tankless 0 mins.
Can I relight my hot water heater?
If your heater’s pilot goes out, you can relight it yourself. Turn the gas regulator valve’s knob to “Pilot,” press down on it and hold it down. This starts the flow of gas to the pilot burner. On some water heater models, you press and hold down a separate red button to start the pilot burner gas flow.
What does it mean when your pilot light won’t stay lit?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
