Table of Contents
Reset power to the product: Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Start a bake cycle. Monitor the oven for one (1) minute to ensure the error code does not display again. Verify oven operation.
How do I reset my Maytag oven control board?
Make sure the Control Lock function is turned OFF. Some ovens may be equipped with Control Lock. Look for “Control Lock” on the oven control console, then reset by, typically, pushing & holding for 3 seconds.
How do I reset my oven control board?
But the first thing you should do is try to perform a hard reset by unplugging the oven, waiting about 30 seconds, and then plugging it back in again. In some cases, this will be enough to reset the control board and get your oven working again.
How do I reset the timer on my Maytag oven?
If your Maytag oven is flashing the time, a power failure has occurred. Reset the time by pressing Clock and then entering the correct time using the temperature control plus and minus keys. Lock in the time by pressing Clock or Start.
Why isn’t my Maytag oven won’t heat up?
A Maytag oven not heating at all may be due to a blown thermal oven fuse. A tripped fuse shuts off power to the oven, making it unable to heat at all. If a thermal fuse trips when overheating isn’t a possibility it’s likely that the fuse is faulty and needs replacement.
How do you unlock the controls on a Maytag oven?
Door is locked when starting or using the oven Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on. Allow the oven to cool, approximately 30-90 minutes, move the latch arm to the left to unlock the door.
What is F3 on Maytag oven?
Both the Maytag oven F3 error code and F4 code indicate there is an issue with the temperature sensor so the cook mode on your oven will stop. Check the sensor to make sure it is closed and there are not issues with the wiring or connection first. If the temperature sensor is damaged or not working, replace it.
How do I know if my oven control board is bad?
“Control board is unresponsive / Oven not working” The display is blank, and none of the buttons are working. It beeps/changes display when you press the buttons, but it still won’t function properly. No beeping/change when you press any button, but the display is still on.
What causes oven control panel not working?
Possible causes are a tripped house circuit breaker for the range, a problem with the outlet cord (not plugged in or broken) or an internal wiring failure. A blown thermal fuse can prevent the control from powering up on some ranges.
Do stoves have a reset button?
The only way to reset the range is by unplugging it for 2-5 minutes.
How do you reset an electric oven after a power cut?
In general, resetting your oven is a straightforward process. You need to purge the control panel of all current commands signals. Then, give your oven a few seconds to boot up. After that, it should be good to go.
How do I fix F9 error on Maytag oven?
How to Remove the F9 Code From Maytag Hold on the “Start/Stop” button for 10 seconds. This will end the beeping. Open the oven door and check the door latch. Spray a little WD-40 onto a washcloth and scrub off any rust or debris on the latch. Press the oven door shut gently. Test the oven.
How do you start a Maytag oven?
How to Light a Maytag Gas Oven Push in and turn any control knob counterclockwise to ignite the corresponding surface or oven burner. Dial the knob to the desired flame setting for cooking. Light a wooden kitchen match during a power outage when you wish to use the Maytag oven.
How do I set the temperature on my Maytag oven?
To Adjust Oven Temperature Calibration: 1. Press and hold BAKE for 5 seconds until the oven display shows the current calibration, for example “0°F CAL” or “00.” 2. Press the TEMP/TIME “+” or “-” keypads to increase or to decrease the temperature in 10°F (5°C) amounts.
Why does my Maytag oven take so long to heat up?
Factors that cause longer preheat times: Avoid leaving the door open for an extended period of time. Newer range/ovens have larger oven cavity than past models which may take longer to preheat. A hidden bake element provides a buffered heat and will take longer to preheat than an exposed bake element.
How do you reset an oven fuse?
Reset the electronic control. Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.
Why does my Maytag oven says lock?
When you place the Maytag oven into self clean mode, the oven door will lock to prevent the door from accidentally being open during cleaning. This is due to the fact that during the cleaning cycle, the oven reaches temperatures far above normal cooking.
How do I turn off the control lock on my Maytag washer?
To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
